- 您现在的位置：买卖IC网 > PDF目录80411 > M38267E8FP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M38267E8FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 0.65 PITCH, PLASTIC, QFP-100 |
| 文件页数： | 21/68页 |
| 文件大小： | 1169K |
| 代理商： | M38267E8FP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3826 Group
28
Timer 1, Timer 2, Timer 3
Timer 1, timer 2, and timer 3 are 8-bit timers. The count source for
each timer can be selected by timer 123 mode register. The timer
latch value is not affected by a change of the count source. How-
ever, because changing the count source may cause an inadvert-
ent count down of the timer. Therefore, rewrite the value of timer
whenever the count source is changed.
qTimer 2 Write Control
If the timer 2 write control bit is “0”, when the value is written in the
address of timer 2, the value is loaded in the timer 2 and the latch
at the same time.
If the timer 2 write control bit is “1”, when the value is written in the
address of timer 2, the value is loaded only in the latch. The value
in the latch is loaded in timer 2 after timer 2 underflows.
qTimer 2 Output Control
When the timer 2 (TOUT) is output enabled, an inversion signal
from pin TOUT is output each time timer 2 underflows.
In this case, set the port P56 shared with the port TOUT to the out-
put mode.
sNote on Timer 1 to Timer 3
When the count source of timers 1 to 3 is changed, the timer
counting value may be changed large because a thin pulse is gen-
erated in count input of timer. If timer 1 output is selected as the
count source of timer 2 or timer 3, when timer 1 is written, the
counting value of timer 2 or timer 3 may be changed large be-
cause a thin pulse is generated in timer 1 output.
Therefore, set the value of timer in the order of timer 1, timer 2
and timer 3 after the count source selection of timer 1 to 3.
Fig. 23 Structure of timer 123 mode register
TOUT output active edge switch bit
0 : Start at “H” output
1 : Start at “L” output
TOUT/
φ output control bit
0 : TOUT/
φ output disabled
1 : TOUT/
φ output enabled
Timer 2 write control bit
0 : Write data in latch and counter
1 : Write data in latch only
Timer 2 count source selection bit
0 : Timer 1 output
1 : f(XIN)/16
(or f(XCIN)/16 in low-speed mode)
Timer 3 count source selection bit
0 : Timer 1 output
1 : f(XIN)/16
(or f(XCIN)/16 in low-speed mode)
Timer 1 count source selection bit
0 : f(XIN)/16
(or f(XCIN)/16 in low-speed mode)
1 : f(XCIN)
Not used (return “0” when read)
Timer 123 mode register
(T123M :address 002916)
Note: Internal clock
φ is f(XCIN)/2 in the low-speed mode.
b7
b0
相关PDF资料 |
PDF描述 |
|---|---|
| MSP430C1111IPW | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20 |
| MB89143AP-SH | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
| MB89F538L-201P | 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDIP64 |
| MB89P485PFM-103 | 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PQFP64 |
| MB90549GSPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38267RLFS | 功能描述:DEV EMULATOR CHIP MCU/8BIT CMOS RoHS:否 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:- 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:* |
| M3826AEFFP#U0 | 制造商:Renesas 功能描述:MCU 8-bit 740 CISC 60KB EPROM 5V 100-Pin PQFP Tray |
| M3826AMFA-221FP#U0 | 制造商:Renesas Electronics Corporation 功能描述: |
| M3826-BK001 | 制造商:Alpha Wire 功能描述: |
| M3826-BK002 | 制造商:Alpha Wire 功能描述: |
发布紧急采购，3分钟左右您将得到回复。