参数资料
型号: M38275EFMXXXHP
厂商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 单芯片8位CMOS微机
文件页数: 26/70页
文件大小: 1112K
代理商: M38275EFMXXXHP
26
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3827 Group
MITSUBISHI MICROCOMPUTERS
f(X
IN
)
1/4
OE
PE FE
1/16
1/16
Data bus
Receive buffer register
Address 0018
16
Receive shift register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Baud rate generator
Address 001C
16
Frequency division ratio 1/(n+1)
ST/SP/PA generator
Transmit buffer register
Data bus
Transmit shift register
Address 0018
16
Transmit shift register shift completion flag (TSC)
Transmit buffer empty flag (TBE)
Address 0019
16
Serial I/O status register
Transmit interrupt request (TI)
STdetector
SP detector
UART control register
Address 001B
16
Character length selection bit
Address 001A
16
BRG count source selection bit
Transmit interrupt source selection bit
Serial I/O synchronous clock selection bit
Clock control circuit
Character length selection bit
7 bits
8 bits
Serial I/O1 control register
P4
6
/S
CLK
P4
4
/R
X
D
P4
5
/T
X
D
(f(X
CIN
) in low-speed mode)
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O mode selection bit of the serial I/O1 control
register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer regis-
ter, but the two buffers have the same address in memory. Since
the shift register cannot be written to or read from directly, transmit
data is written to the transmit buffer, and receive data is read from
the receive buffer.
The transmit buffer can also hold the next data to be transmitted,
and the receive buffer register can hold a character while the next
character is being received.
Fig. 23 Block diagram of UART serial I/O1
Fig. 24 Operation of UART serial I/O1 function
TSC=0
TBE=1
RBF=0
TBE=0
TBE=0
RBF=1
RBF=1
ST
D
0
D
1
SP
D
0
D
1
ST
SP
TBE=1
TSC=1
8
ST
D
0
D
1
SP
D
0
D
1
ST
SP
Transmit buffer write signal
8
Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bits
1 or 0 parity bit
1 or 2 stop bit (s)
1 :
Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2 :
The transmit interrupt (TI) can be selected to occur when either the TBE or TSC flag becomes “1” by the setting of the transmit interrupt source
selection bit (TIC) of the serial I/O1 control register.
3 :
The receive interrupt (RI) is set when the RBF flag becomes “1”.
4 :
After data is written to the transmit buffer register when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Notes
Serial output T
X
D
Serial input R
X
D
Receive buffer read signal
Transmit or receive clock
相关PDF资料
PDF描述
M38275M6-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38275M6-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38275M6-XXXGP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38275M7-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38275M7-XXXGP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相关代理商/技术参数
参数描述
M3828 BK001 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 1000'
M3828 BK002 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 500'
M3828 BK005 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 100'
M3828 BK199 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 3000=3000'
M3829 BK001 制造商:Alpha Wire Company 功能描述:CBL 4COND 16AWG BLK 1000'