- 您现在的位置：买卖IC网 > PDF目录80529 > M38503M2A-XXXFP 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDSO42 PDF资料下载
参数资料
| 型号： | M38503M2A-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDSO42 |
| 封装： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件页数： | 43/99页 |
| 文件大小： | 1419K |
| 代理商： | M38503M2A-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页
48
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
CLOCK GENERATING CIRCUIT
The 3850 group (spec. H/A) has two built-in oscillation circuits. An
oscillation circuit can be formed by connecting a resonator be-
tween XIN and XOUT (XCIN and XCOUT). Use the circuit constants
in accordance with the resonator manufacturer’s recommended
values. No external resistor is needed between XIN and XOUT
since a feed-back resistor exists on-chip. However, an external
feed-back resistor is needed between XCIN and XCOUT.
Immediately after power on, only the XIN oscillation circuit starts
oscillating, and XCIN and XCOUT pins function as I/O ports.
Frequency Control
(1) Middle-speed mode
The internal clock
φ is the frequency of XIN divided by 8. After re-
set is released, this mode is selected.
(2) High-speed mode
The internal clock
φ is half the frequency of XIN.
(3) Low-speed mode
The internal clock
φ is half the frequency of XCIN.
sNote
If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and XCIN oscillations. The sufficient time
is required for the sub-clock to stabilize, especially immediately af-
ter power on and at returning from the stop mode. When switching
the mode between middle/high-speed and low-speed, set the fre-
quency on condition that f(XIN) > 3f(XCIN).
(4) Low power dissipation mode
The low power consumption operation can be realized by stopping
the main clock XIN in low-speed mode. To stop the main clock, set
bit 5 of the CPU mode register to “1.” When the main clock XIN is
restarted (by setting the main clock stop bit to “0”), set sufficient
time for oscillation to stabilize.
The sub-clock XCIN-XCOUT oscillating circuit can not directly input
clocks that are generated externally. Accordingly, make sure to
cause an external resonator to oscillate.
Oscillation Control
(1) Stop mode
If the STP instruction is executed, the internal clock
φ stops at an
“H” level, and XIN and XCIN oscillation stops. When the oscillation
stabilizing time set after STP instruction released bit is “0,” the
prescaler 12 is set to “FF16” and timer 1 is set to “0116.” When the
oscillation stabilizing time set after STP instruction released bit is
“1,” set the sufficient time for oscillation of used oscillator to stabi-
lize since nothing is set to the prescaler 12 and timer 1.
Either XIN or XCIN divided by 16 is input to the prescaler 12 as
count source. Oscillator restarts when an external interrupt is re-
ceived, but the internal clock
φ is not supplied to the CPU (remains
at “H”) until timer 1 underflows. The internal clock
φ is supplied for
the first time, when timer 1 underflows. This ensures time for the
clock oscillation using the ceramic resonators to be stabilized.
When the oscillator is restarted by reset, apply “L” level to the
RESET pin until the oscillation is stable since a wait time will not
be generated.
Fig. 52 Ceramic resonator circuit
Fig. 53 External clock input circuit
(2) Wait mode
If the WIT instruction is executed, the internal clock
φ stops at an
“H” level, but the oscillator does not stop. The internal clock
φ re-
starts at reset or when an interrupt is received. Since the oscillator
does not stop, normal operation can be started immediately after
the clock is restarted.
To ensure that the interrupts will be received to release the STP or
WIT state, their interrupt enable bits must be set to “1” before ex-
ecuting of the STP or WIT instruction.
When releasing the STP state, the prescaler 12 and timer 1 will
start counting the clock XIN divided by 16. Accordingly, set the
timer 1 interrupt enable bit to “0” before executing the STP instruc-
tion.
sNote
When using the oscillation stabilizing time set after STP instruction
released bit set to “1”, evaluate time to stabilize oscillation of the
used oscillator and set the value to the timer 1 and prescaler 12.
3850 Group (Spec. H/A)
XCIN
XCOUT
XIN
XOUT
CIN
COUT
CCIN
CCOUT
Rf
Rd
XCIN
XCOUT
XIN
XOUT
CCIN
CCOUT
Rf
Rd
Open
External oscillation
circuit
Vcc
Vss
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8255ZULHDX | 32-BIT, 250 MHz, RISC PROCESSOR, PBGA480 |
| MC68HC705J1ACSD | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC705P6AP | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| MB89P538-201PF | 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PQFP64 |
| MB89P485LPFM-102 | 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38503M4A-210SP | 制造商:Renesas Electronics Corporation 功能描述: |
| M38504E6FP | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 24K 42-SSOP - Trays |
| M38504E6FP#U0 | 功能描述:MCU 4.0/5.5V 24K PB-FREE 42-SSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38504M6202F | 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC |
| M38504M6211F | 制造商:Panasonic Industrial Company 功能描述:IC SUB FOR P-M38504M6202F |
发布紧急采购，3分钟左右您将得到回复。