参数资料
型号: M38C81M2-XXXFP
厂商: Mitsubishi Electric Corporation
英文描述: PCB COPPER CLAD 6X9 1 SIDE
中文描述: 单芯片8位CMOS微机
文件页数: 9/51页
文件大小: 874K
代理商: M38C81M2-XXXFP
9
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
38C8 Group
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5 flags
which indicate the status of the processor after an arithmetic opera-
tion and 3 flags which decide MCU operation. Branch operations can
be performed by testing the Carry (C) flag , Zero (Z) flag, Overflow
(V) flag, or the Negative (N) flag. In decimal mode, the Z, V, N flags
are not valid.
Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
Bit 1: Zero flag (Z)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is
0
, and cleared if the result is anything other
than
0
.
Bit 2: Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
Interrupts are disabled when the I flag is
1
.
Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is
0
; decimal arithmetic is executed when it is
1
.
Decimal correction is automatic in decimal mode. Only the ADC
Bit 4: Break flag (B)
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always
0
. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to
1
.
Bit 5: Index X mode flag (T)
When the T flag is
0
, arithmetic operations are performed
between accumulator and memory. When the T flag is
1
, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
Bit 7: Negative flag (N)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
Table 4 Set and clear instructions of each bit of processor status register
C flag
SEC
CLC
Set instruction
Clear instruction
Z flag
I flag
SEI
CLI
D flag
SED
CLD
B flag
T flag
SET
CLT
V flag
CLV
N flag
相关PDF资料
PDF描述
M38C83M4-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C84EA-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C88E1-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C88E2-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C88E3-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相关代理商/技术参数
参数描述
M38D20F1XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D20F1XXXHP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D20F2XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D20F2XXXHP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D20F3XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER