- 您现在的位置：买卖IC网 > PDF目录80445 > M41T11MH6F (STMICROELECTRONICS) REAL TIME CLOCK, PDSO28 PDF资料下载
参数资料
| 型号： | M41T11MH6F |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | REAL TIME CLOCK, PDSO28 |
| 封装： | 0.330 INCH, LEAD FREE, PLASTIC, SOH-28 |
| 文件页数： | 6/30页 |
| 文件大小： | 250K |
| 代理商： | M41T11MH6F |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Clock operation
M41T11
3
Clock operation
The eight byte clock register (see Table 3) is used to both set the clock and to read the date
and time from the clock, in a binary coded decimal format. Seconds, minutes, and hours are
contained within the first three registers. Bits D6 and D7 of clock register 2 (hours register)
contain the CENTURY ENABLE bit (CEB) and the CENTURY bit (CB). Setting CEB to a '1'
will cause CB to toggle, either from '0' to '1' or from '1' to '0' at the turn of the century
(depending upon its initial state). If CEB is set to a '0', CB will not toggle. Bits D0 through D2
of register 3 contain the day (day of week). Registers 4, 5 and 6 contain the date (day of
month), month and years. The final register is the control register (this is described in the
clock calibration section). Bit D7 of register 0 contains the STOP bit (ST). Setting this bit to a
'1' will cause the oscillator to stop. If the device is expected to spend a significant amount of
time on the shelf, the oscillator may be stopped to reduce current drain. When reset to a '0'
the oscillator restarts within one second.
Note:
In order to guarantee oscillator startup after the initial power-up, set the ST bit to a '1,' then
reset this bit to a '0.' This sequence enables a “kick start” circuit which aids the oscillator
startup during worst case conditions of voltage and temperature.
The seven clock registers may be read one byte at a time, or in a sequential block. The
control register (address location 7) may be accessed independently. Provision has been
made to assure that a clock update does not occur while any of the seven clock addresses
are being read. If a clock address is being read, an update of the clock registers will be
delayed by 250 ms to allow the read to be completed before the update occurs. This will
prevent a transition of data during the read.
Note:
This 250 ms delay affects only the clock register update and does not alter the actual clock
time.
相关PDF资料 |
PDF描述 |
|---|---|
| MC9S08RD16CFJ | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| MCF5275CVM166 | 32-BIT, 166 MHz, RISC PROCESSOR, PBGA256 |
| MC9S12DJ128BCPV | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 |
| MC9S12XDP512CPV | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP112 |
| MC68020FC20 | 32-BIT, 20 MHz, MICROPROCESSOR, PQFP132 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M41T11MH6F-CUT TAPE | 制造商:ST 功能描述:M41T11 Series 2 to 5.5 V Serial I2C Real Time Clock Surface Mount - SOH-28 |
| M41T11MH6TR | 制造商:STMicroelectronics 功能描述:REAL TIME CLOCK SERL 64BYTE 28PIN SOH - Tape and Reel |
| M41T11SH | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 bit 64b x8 Serial Access TIMEKEEPER SRAM |
| M41T256Y | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC |
| M41T256Y_07 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256Kbit (32K x 8) serial RTC |
发布紧急采购，3分钟左右您将得到回复。