- 您现在的位置：买卖IC网 > PDF目录383300 > M470L3324CU0-LB3 (SAMSUNG SEMICONDUCTOR CO. LTD.) DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb C-die PDF资料下载
参数资料
| 型号： | M470L3324CU0-LB3 |
| 厂商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb C-die |
| 中文描述： | DDR SDRAM的缓冲模块18 4针缓冲模块的基于C的512Mb芯片 |
| 文件页数： | 14/17页 |
| 文件大小： | 225K |
| 代理商： | M470L3324CU0-LB3 |
DDR SDRAM
256MB, 512MB Unbuffered SODIMM
Rev. 1.2 June 2005
b. Pulldown slew rate is measured under the test conditions shown in Figure 3.
Output
Test point
VDDQ
50
Figure 3 : Pulldown slew rate test load
c. Pullup slew rate is measured between (VDDQ/2 - 320 mV +/- 250 mV)
Pulldown slew rate is measured between (VDDQ/2 + 320 mV +/- 250 mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output switching.
Example : For typical slew rate, DQ0 is switching
For minmum slew rate, all DQ bits are switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
d. Evaluation conditions
Typical : 25
°
C (T Ambient), VDDQ = 2.5V(for DDR266/333) and 2.6V(for DDR400), typical process
Minimum : 70
°
C (T Ambient), VDDQ = 2.3V(for DDR266/333) and 2.5V(for DDR400), slow - slow process
Maximum : 0
°
C (T Ambient), VDDQ = 2.7V(for DDR266/333) and 2.7V(for DDR400), fast - fast process
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature and voltage range.
For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation.
f. Verified under typical conditions for qualification purposes.
g. TSOPII package divices only.
h. Only intended for operation up to 266 Mbps per pin.
i. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5V/ns as shown in Table 2. The Input slew rate is
based on the lesser of the slew rates detemined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
j. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables 3 & 4. Input slew rate
is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, Input slew rate is based on the lesser of the slew rates determined by either
VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions. The delta rise/fall rate is calculated as: {1/(Slew Rate1)} - {1/(Slew Rate2)}
For example : If Slew Rate 1 is 0.5 V/ns and slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is - 0.5ns/V . Using the table given, this
would result in the need for an increase in tDS and tDH of 100 ps.
k. Table 3 is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the lesser on the lesser of
the AC - AC slew rate and the DC- DC slew rate. The inut slew rate is based on the lesser of the slew rates deter mined by either VIH(ac) to VIL(ac) or
VIH(DC) to VIL(DC), and similarly for rising transitions.
m. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi tions through the
DC region must be monotonic.
a. Pullup slew rate is characteristized under the test conditions as shown in Figure 2.
Output
Test point
VSSQ
50
Figure 2 : Pullup slew rate test load
15.0 System Notes:
相关PDF资料 |
PDF描述 |
|---|---|
| M470L3324CU0-LCC | DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb C-die |
| M470L6524DU0-LA2 | DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
| M470L6524DU0-CCC | DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
| M470L3324DU0-LA2 | DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
| M470L3324DU0-LB0 | DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M470L3324CU0-LCC | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb C-die |
| M470L3324DU0 | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
| M470L3324DU0-CA2 | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
| M470L3324DU0-CB0 | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
| M470L3324DU0-CB3 | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:DDR SDRAM Unbuffered Module 18 4 pin Unbuffered Module based on 512Mb D-die 66 TSOP-II & 54 sTSOP-II with Pb-Free (RoHS compliant) |
发布紧急采购，3分钟左右您将得到回复。