- 您现在的位置：买卖IC网 > PDF目录45050 > M48T201V-85MH1E (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PDSO44 PDF资料下载
参数资料
| 型号： | M48T201V-85MH1E |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO44 |
| 封装： | SNAPHAT, ROHS COMPLIANT, PLASTIC, SOIC-44 |
| 文件页数： | 16/37页 |
| 文件大小： | 311K |
| 代理商： | M48T201V-85MH1E |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
M48T201Y, M48T201V
Clock operation
The oscillation rate of crystals changes with temperature (see Figure 10 on page 24). The
M48T201Y/V design employs periodic counter correction. The calibration circuit adds or
subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in
The number of times pulses which are blanked (subtracted, negative calibration) or split
(added, positive calibration) depends upon the value loaded into the five calibration bits
found in the control register. Adding counts speeds the clock up, subtracting counts slows
the clock down.
The calibration bits occupy the five lower order bits (D4-D0) in the control register 7FFF8h.
These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a
sign bit; '1' indicates positive calibration, '0' indicates negative calibration (see Figure 11 on
page 24). Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may,
once per minute, have one second either shortened by 128 or lengthened by 256 oscillator
cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minute cycle
will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on.
Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator
cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or –2.034 ppm of
adjustment per calibration step in the calibration register. Assuming that the oscillator is
running at exactly 32,768 Hz, each of the 31 increments in the calibration byte would
represent +10.7 or –5.35 seconds per month which corresponds to a total range of +5.5 or –
2.75 minutes per month.
Two methods are available for ascertaining how much calibration a given M48T201Y/V may
require. The first involves setting the clock, letting it run for a month and comparing it to a
known accurate reference and recording deviation over a fixed period of time. Calibration
values, including the number of seconds lost or gained in a given period, can be found in the
STMicroelectronics application note AN934, “TIMEKEEPER calibration.” This allows the
designer to give the end user the ability to calibrate the clock as the environment requires,
even if the final product is packaged in a non-user serviceable enclosure. The designer
could provide a simple utility that accesses the calibration byte.
The second approach is better suited to a manufacturing environment, and involves the use
of the IRQ/FT pin. The pin will toggle at 512 Hz, when the stop bit (ST, D7 of 7FFF9h) is '0,'
the frequency test bit (FT, D6 of 7FFFCh) is '1,' the alarm flag enable bit (AFE, D7 of
7FFF6h) is '0,' and the watchdog steering bit (WDS, D7 of 7FFF7h) is '1' or the watchdog
register (7FFF7h=0) is reset.
Note:
A 4-second settling time must be allowed before reading the 512 Hz output.
Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at
the test temperature. For example, a reading of 512.010124 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10 (WR001010) to be loaded into the calibration byte
for correction. Note that setting or changing the calibration byte does not affect the
frequency test output frequency.
The IRQ/FT pin is an open drain output which requires a pull-up resistor to VCC for proper
operation. A 500-10 k
Ω resistor is recommended in order to control the rise time. The FT bit
is cleared on power-down.
相关PDF资料 |
PDF描述 |
|---|---|
| M48T201Y-70MH1E | 1 TIMER(S), REAL TIME CLOCK, PDSO44 |
| M48T201V-85MH6TR | 1 TIMER(S), REAL TIME CLOCK, PDSO44 |
| M48T201Y-70MH6 | 1 TIMER(S), REAL TIME CLOCK, PDSO44 |
| M48T201Y-70MHTR | 1 TIMER(S), REAL TIME CLOCK, PDSO44 |
| M48T212V-70MH1 | 0 TIMER(S), REAL TIME CLOCK, PDSO44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M48T201V-85MH1F | 功能描述:监控电路 SRAM TK Controller RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| M48T201V-85MH1TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5.0 or 3.3V TIMEKEEPER㈢ supervisor |
| M48T201VMH | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V TIMEKEEPER CONTROLLER |
| M48T201VSH | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V TIMEKEEPER CONTROLLER |
| M48T201Y | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:3.3V-5V TIMEKEEPER CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。