参数资料
型号: M68HC05
厂商: Motorola, Inc.
英文描述: M68HC05 MICROCONTROLLERS
中文描述: M68HC05系列微控制器
文件页数: 144/222页
文件大小: 2253K
代理商: M68HC05
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页当前第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页
Technical Data
MC68HC705C8A
Rev. 3
144
Serial Peripheral Interface (SPI)
MOTOROLA
Serial Peripheral Interface (SPI)
11.4.2 Pin Functions in Slave Mode
Clearing the MSTR bit in the SPCR configures the SPI for operation in
slave mode. The slave-mode functions of the SPI pins are:
PD4/SCK (serial clock)
In slave mode, the PD4/SCK pin is the
input for the synchronizing clock signal from the master SPI.
PD3/MOSI (master output, slave input)
In slave mode, the
PD3/MOSI pin is the serial input.
PD2/MISO (master input, slave output)
In slave mode, the
PD2/MISO pin is the serial output.
PD5/SS (slave select)
In slave mode, the PD5/SS pin enables
the SPI for data and serial clock reception from a master SPI.
When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI
message. When CPHA = 1, SS may be left low for several SPI
characters. In cases with only one SPI slave MCU, the slave MCU SS
line can be tied to V
SS
as long as CPHA = 1 clock modes are used.
The WCOL flag bit can be improperly set when attempting the first
transmission after a reset if these conditions are present: MSTR = 0,
CPOL = 0, CPHA = 1, SS pin = 0, and SCK pin = 1. The reset states of
the CPOL and CPHA bits are 0 and 1, respectively. Under normal
operating conditions (CPOL = 0, CPHA = 1), the SCK input will be low.
The incorrect setting of the WCOL bit can be prevented in two ways:
1.
Send a dummy transmission after reset, clear the WCOL flag, and
then proceed with the real transmission.
2.
Use the MSTR bit in the SPCR (SPI control register). This is
accomplished by setting the MSTR bit at the same time the CPOL
and CPHA bits are programmed to the desired logic levels. Then,
the data register can be written to if desired. After this, the MSTR
bit should be set to a logic 0, the SPE (SPI enable bit) should be
set to a logic 1, and the CPOL, CPHA, SPR1, and SPR0 bits set
to the desired logic levels. If this procedure is followed after a reset
and before the first access to the SPDR, the WCOL flag will not be
set.
相关PDF资料
PDF描述
M68HC11CPU Single-Chip Microcontrollers (AMCU)
M68HC11 Technical Data
M6M80011 1024 BIT ELECTRICALLY ERASABLE AND PROGRAMMABLE ROM
M6M80011AP 1024 BIT ELECTRICALLY ERASABLE AND PROGRAMMABLE ROM
M6M80011FP 1024 BIT ELECTRICALLY ERASABLE AND PROGRAMMABLE ROM
相关代理商/技术参数
参数描述
M68HC05_13 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC05 Microcontrollers
M68HC05EVS 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Motorola M68HC05 Family Evaluation System
M68HC05M68H 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:HCMOS Microcontroller Unit
M68HC08 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers
M68HC08M6 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:HCMOS Microcontroller Unit