- 您现在的位置：买卖IC网 > PDF目录359119 > M95080-WMN6 (意法半导体) 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock PDF资料下载
参数资料
| 型号： | M95080-WMN6 |
| 厂商： | 意法半导体 |
| 元件分类： | DRAM |
| 英文描述： | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| 中文描述： | 16Kbit和8Kbit SPI总线串行EEPROM的高速时钟 |
| 文件页数： | 9/39页 |
| 文件大小： | 590K |
| 代理商： | M95080-WMN6 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
9/39
M95640, M95320
OPERATING FEATURES
Power-up
When the power supply is turned on, V
CC
rises
from V
SS
to V
CC
.
During this time, the Chip Select (S) must be al-
lowed to follow the V
CC
voltage. It must not be al-
lowed to float, but should be connected to V
CC
via
a suitable pull-up resistor.
As a built in safety feature, Chip Select (S) is edge
sensitive as well as level sensitive. After Power-
up, the device does not become selected until a
falling edge has first been detected on Chip Select
(S). This ensures that Chip Select (S) must have
been High, prior to going Low to start the first op-
eration.
Power On Reset: V
CC
Lock-Out Write Protect
In order to prevent data corruption and inadvertent
Write operations during Power-up, a Power On
Reset (POR) circuit is included. The internal reset
is held active until V
CC
has reached the POR
threshold value, and all operations are disabled –
the device will not respond to any command. In the
same way, when V
CC
drops from the operating
voltage, below the POR threshold value, all oper-
ations are disabled and the device will not respond
to any command.
A stable and valid V
CC
must be applied before ap-
plying any logic signal.
Power-down
At Power-down, the device must be deselected.
Chip Select (S) should be allowed to follow the
voltage applied on V
CC
.
Active Power and Stand-by Power Modes
When Chip Select (S) is Low, the device is en-
abled, and in the Active Power mode. The device
consumes I
CC
, as specified in Tables 13 to 17.
When Chip Select (S) is High, the device is dis-
abled. If an Erase/Write cycle is not currently in
progress, the device then goes in to the Stand-by
Power mode, and the device consumption drops
to I
CC1
.
Hold Condition
The Hold (HOLD) signal is used to pause any se-
rial communications with the device without reset-
ting the clocking sequence.
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
To enter the Hold condition, the device must be
selected, with Chip Select (S) Low.
Normally, the device is kept selected, for the whole
duration of the Hold condition. Deselecting the de-
vice while it is in the Hold condition, has the effect
of resetting the state of the device, and this mech-
anism can be used if it is required to reset any pro-
cesses that had been in progress.
The Hold condition starts when the Hold (HOLD)
signal is driven Low at the same time as Serial
Clock (C) already being Low (as shown in Figure
7).
The Hold condition ends when the Hold (HOLD)
signal is driven High at the same time as Serial
Clock (C) already being Low.
Figure 7 also shows what happens if the rising and
falling edges are not timed to coincide with Serial
Clock (C) being Low.
Figure 7. Hold Condition Activation
AI02029D
HOLD
C
Hold
Condition
Hold
Condition
相关PDF资料 |
PDF描述 |
|---|---|
| M95080-WMN6T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95080BN | Octal Edge-Triggered D-Type Flip-Flops with 3-State Outputs 20-TSSOP -40 to 85 |
| M95080-WDW3 | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95080-WMN3 | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95080-WBN1T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M95080-WMN6P | 功能描述:电可擦除可编程只读存储器 2.5 V to 5.5V EE RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M95080-WMN6T | 功能描述:电可擦除可编程只读存储器 5.5V 8K (1Kx8) RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M95080-WMN6TP | 功能描述:电可擦除可编程只读存储器 2.5 V to 5.5V 8K RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M95080-WMN6TP/S | 制造商:STMicroelectronics 功能描述:EEPROM SERL-SPI 8KBIT 1KX8 3.3V/5V 8PIN SO N - Tape and Reel |
| M95080-WMN6TP-CUT TAPE | 制造商:ST 功能描述:M95080 Series 8 Kb (1 K x 8) 5.5 V Serial SPI Bus EEPROM with High-Speed Clock |
发布紧急采购，3分钟左右您将得到回复。