- 您现在的位置：买卖IC网 > PDF目录1935 > MAX1021BETX+ (Maxim Integrated Products)IC ADC/DAC 10BIT W/FIFO 36-TQFN PDF资料下载
参数资料
| 型号： | MAX1021BETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC/DAC 10BIT W/FIFO 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | ADC，DAC |
| 分辨率（位）： | 10 b |
| 采样率（每秒）： | 300k |
| 数据接口： | 串行 |
| 电压电源： | 模拟和数字 |
| 电源电压： | 2.7V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MAX1021/MAX1043
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
16
______________________________________________________________________________________
Detailed Description
The MAX1021/MAX1043 integrate a multichannel 10-bit
ADC and a 10-bit DAC in a single IC. These devices
also include a temperature sensor and configurable
GPIOs with a 25MHz SPI-/QSPI-/MICROWIRE-compati-
ble serial interface. The ADC is available in an 8 input-
channel version. The DAC outputs settle within 2.0s,
and the ADC has a 225ksps conversion rate.
These devices include an internal reference (2.5V) pro-
viding a well-regulated, low-noise reference for both the
ADC and DAC. Programmable reference modes for the
ADC and DAC allow the use of an internal reference, an
external reference, or a combination of both. Features
such as an internal ±1°C accurate temperature sensor,
FIFO, scan modes, programmable internal or external
clock modes, data averaging, and AutoShutdown allow
users to minimize both power consumption and proces-
sor requirements. The low glitch energy (4nVs) and
low digital feedthrough (0.5nVs) of the integrated
DACs make these devices ideal for digital control of
fast-response closed-loop systems.
The devices are guaranteed to operate with a supply
voltage from +2.7V to +5.25V. They consume 2.5mA at
225ksps throughput, only 0.22A at 1ksps throughput,
and under 0.2A in shutdown mode. The MAX1021/
MAX1043 offer four GPIOs that can be configured as
inputs or outputs.
Figure 1 shows the MAX1021 functional diagram. The
MAX1021/MAX1043 only include the GPIO A0, A1, GPIO
C0, C1 blocks. The output-conditioning circuitry takes the
internal parallel data bus and converts it to a serial data
format at DOUT, with the appropriate wake-up timing. The
arithmetic logic unit (ALU) performs the averaging func-
tion.
SPI-Compatible Serial Interface
The MAX1021/MAX1043 feature a serial interface that is
compatible with SPI and MICROWIRE devices. For SPI,
ensure the SPI bus master (typically a microcontroller
(C)) runs in master mode so that it generates the
serial-clock signal. Select the SCLK frequency of
25MHz or less, and set the clock polarity (CPOL) and
phase (CPHA) in the C control registers to the same
value. The MAX1021/MAX1043 operate with SCLK
idling high or low, and thus operate with CPOL = CPHA
= 0 or CPOL = CPHA = 1. Set
CS low to latch any input
data at DIN on the falling edge of SCLK. Output data at
DOUT is updated on the falling edge of SCLK in clock
modes 00, 01, and 10. Output data at DOUT is updated
on the rising edge of SCLK in clock mode 11. See
Figures 6–11. Bipolar true-differential results and tem-
perature-sensor results are available in two’s comple-
ment format, while all other results are in binary.
A high-to-low transition on
CS initiates the data-input
operation. Serial communications to the ADC always
begin with an 8-bit command byte (MSB first) loaded
from DIN. The command byte and the subsequent data
bytes are clocked from DIN into the serial interface on
the falling edge of SCLK. The serial-interface and fast-
interface circuitry is common to the ADC, DAC, and
GPIO sections. The content of the command byte
determines whether the SPI port should expect 8, 16, or
24 bits and whether the data is intended for the ADC,
DAC, or GPIOs (if applicable). See Table 1. Driving
CS
high resets the serial interface.
The conversion register controls ADC channel selec-
tion, ADC scan mode, and temperature-measurement
requests. See Table 4 for information on writing to the
conversion register. The setup register controls the
clock mode, reference, and unipolar/bipolar ADC con-
figuration. Use a second byte, following the first, to
write to the unipolar-mode or bipolar-mode registers.
See Table 5 for details of the setup register and see
Tables 6, 7, and 8 for setting the unipolar- and bipolar-
mode registers. Hold
CS low between the command
byte and the second and third byte. The ADC averag-
ing register is specific to the ADC. See Table 9 to
address that register. Table 11 shows the details of the
reset register.
Begin a write to the DAC by writing 0001XXXX as a
command byte. The last 4 bits of this command byte
are don’t-care bits. Write another 2 bytes (holding
CS
low) to the DAC interface register following the com-
mand byte to select the appropriate DAC and the data
to be written to it. See the
DAC Serial Interface section
and Tables 10, 17, and 18.
Write to the GPIOs (if applicable) by issuing a com-
mand byte to the appropriate register. Writing to the
MAX1021/MAX1043 GPIOs requires 1 additional byte
following the command byte. See Tables 12–16 for
details on GPIO configuration, writes, and reads. See
the
GPIO Command section. Command bytes written to
the GPIOs on devices without GPIOs are ignored.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1042BETX+ | IC ADC/DAC 10BIT W/FIFO 36TQFN |
| MAX1057BETM+T | IC ADC/DAC 10BIT 48-TQFN-EP |
| MAX11041ETC+T | IC REMOTE CTRLR WIRED 12-TQFN |
| MAX11043ATL+T | IC ADC 16BIT W/DAC 40-TQFN-EP |
| MAX11359AETL+T | IC DAS SYSTEM 16BIT 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1021BETX+ | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns/GPIO Ports RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX1021BETX+T | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns/GPIO Ports RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX1021BETX-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX1022 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
| MAX1022BETX | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
发布紧急采购，3分钟左右您将得到回复。