- 您现在的位置：买卖IC网 > PDF目录9933 > MAX1031BCTI+ (Maxim Integrated Products)IC ADC 10BIT 300KSPS 28-TQFN-EP PDF资料下载
参数资料
| 型号： | MAX1031BCTI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/22页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 300KSPS 28-TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 位数： | 10 |
| 采样率（每秒）： | 300k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.67W |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
| 输入数目和类型： | 16 个单端，单极；16 个单端，双极；8 个差分，单极；8 个差分，双极 |
MAX1027/MAX1029/MAX1031
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
19
clock. Scanning and averaging are disabled, and the
conversion result is available at DOUT during the con-
version. See Figure 7 for clock mode 11 timing.
Initiate a conversion by writing a byte to the conversion
register followed by 16 SCLK cycles. If
CS is pulsed
high between the eighth and ninth cycles, the pulse
width must be less than 100μs. To continuously convert
at 16 cycles per conversion, alternate 1 byte of zeros
between each conversion byte.
If reference mode 00 is requested, or if an external ref-
erence is selected but a temperature measurement is
being requested, wait 65μs with
CS high after writing
the conversion byte to extend the acquisition and allow
the internal reference to power up. To perform a tem-
perature measurement, write 24 bytes (192 cycles) of
zeros after the conversion byte. The temperature result
appears on DOUT during the last 2 bytes of the 192
cycles.
Partial Reads and Partial Writes
If the first byte of an entry in the FIFO is partially read
(
CS is pulled high after fewer than 8 SCLK cycles), the
second byte of data that is read out contains the next 8
bits (not b7–b0). The remaining bits are lost for that
entry. If the first byte of an entry in the FIFO is read out
fully, but the second byte is read out partially, the rest
of the entry is lost. The remaining data in the FIFO is
uncorrupted and can be read out normally after taking
CS low again, as long as the 4 leading bits (normally
zeros) are ignored. Internal registers that are written
partially through the SPI contain new values, starting at
the MSB up to the point that the partial write is stopped.
The part of the register that is not written contains previ-
ously written values. If
CS is pulled low before EOC
goes low, a conversion cannot be completed and the
FIFO is corrupted.
Transfer Function
Figure 8 shows the unipolar transfer function for single-
ended or differential inputs. Figure 9 shows the bipolar
transfer function for differential inputs. Code transitions
occur halfway between successive-integer LSB values.
Output coding is binary, with 1 LSB = VREF / 1024V for
unipolar and bipolar operation, and 1 LSB = 0.125°C
for temperature measurements.
Layout, Grounding, and Bypassing
For best performance, use PC boards. Do not use wire-
wrap boards. For the TQFN package, connect its
exposed pad to GND. Board layout should ensure that
digital and analog signal lines are separated from each
other. Do not run analog and digital (especially clock)
signals parallel to one another or run digital lines under-
neath the MAX1027/MAX1029/MAX1031 package. High-
frequency noise in the VDD power supply can affect
performance. Bypass the VDD supply with a 0.1μF
capacitor to GND, close to the VDD pin. Minimize capac-
itor lead lengths for best supply-noise rejection. If the
power supply is very noisy, connect a 10
Ω resistor in
series with the supply to improve power-supply filtering.
CS
DOUT
SCLK
DIN
EOC
MSB1
LSB1
MSB2
(ACQUISITION1)
(ACQUISITION2)
(CONVERSION1)
(CONVERSION BYTE)
EXTERNALLY TIMED ACQUISITION, SAMPLING AND CONVERSION WITHOUT CNVST. X = DON'T CARE.
Figure 7. Clock Mode 11
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21F-CU-B1 | CONVERTER MOD DC/DC 72V 200W |
| VI-21D-CU-B1 | CONVERTER MOD DC/DC 85V 200W |
| MS27484E12F22S | CONN PLUG 22POS STRAIGHT W/SCKT |
| MS27474T14B35PC | CONN RCPT 37POS JAM NUT W/PINS |
| IDT72V281L20PF | IC FIFO 32768X18 20NS 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1031BCTI+ | 功能描述:模数转换器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1031BCTI+T | 功能描述:模数转换器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1031BCTI-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1031BEEG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1031BEEG+ | 功能描述:模数转换器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。