- 您现在的位置：买卖IC网 > PDF目录2085 > MAX1036LEKA+T (Maxim Integrated Products)IC ADC 8BIT LP SERIAL SOT23-8 PDF资料下载
参数资料
| 型号： | MAX1036LEKA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/23页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT LP SERIAL SOT23-8 |
| 标准包装： | 2,500 |
| 位数： | 8 |
| 采样率（每秒）： | 188k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.75mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个伪差分，单极；2 个伪差分，双极 |
a START condition followed by 7 address bits and a
read bit (R/W = 1). If the address byte is successfully
received, the MAX1036–MAX1039 (slave) issue an
acknowledge. The master then reads from the slave.
After the master has received the results, it can issue
an acknowledge if it wants to continue reading or a not
acknowledge if it no longer wishes to read. If the
MAX1036–MAX1039 receive a not acknowledge, they
release SDA allowing the master to generate a STOP
or repeated START. See the
Clock Mode and Scan
Mode sections for detailed information on how data is
obtained and converted.
Clock Mode
The clock mode determines the conversion clock, the
acquisition time, and the conversion time. The clock
mode also affects the scan mode. The state of the
setup byte’s CLK bit determines the clock mode (Table
1). At power-up, the MAX1036–MAX1039 default to
internal clock mode (CLK = zero).
Internal Clock
When configured for internal clock mode (CLK = zero),
the MAX1036–MAX1039 use their internal oscillator as
the conversion clock. In internal clock mode, the
MAX1036–MAX1039 begin tracking analog input on the
ninth falling clock edge of a valid slave address byte.
Two internal clock cycles later, the analog signal is
acquired and the conversion begins. While tracking
and converting the analog input signal, the
MAX1036–MAX1039 hold SCL low (clock stretching).
After the conversion completes, the results are stored
MAX1036–MAX1039
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
4-/12-Channel 2-Wire Serial 8-Bit ADCs
______________________________________________________________________________________
13
110
1
00
0
R/W
A
SLAVE ADDRESS
S
SCL
SDA
1
2
34
567
8
9
DEVICE
SLAVE ADDRESS
1100100
1100101
MAX1036/MAX1037
MAX1038/MAX1039
Figure 7. MAX1036/MAX1037 Slave Address Byte
000
1
0X
X
A
HS-MODE MASTER CODE
SCL
SDA
S
Sr
F/S-MODE
HS-MODE
Figure 8. F/S-Mode to HS-Mode Transfer
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1060AEEI+ | IC ADC 10BIT 400KSPS 28-QSOP |
| MAX1062AEUB+ | IC ADC 14BIT 200KSPS 10-UMAX |
| MAX1066BEUP+ | IC ADC 14BIT 165KSPS 20TSSOP |
| MAX1067BCEE+ | IC ADC 14-BIT 200KSPS 16-QSOP |
| MAX1069BEUD+ | IC ADC 14BIT I2C 58KSPS 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1036-MAX1039 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1036MEKA | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product 制造商:Rochester Electronics LLC 功能描述: |
| MAX1036MEKA+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 188KSPS 8BIT SERL 8PIN SOT-23 - Cut Tape Product |
| MAX1036MEKA+T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1036MEKA-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。