- 您现在的位置：买卖IC网 > PDF目录9882 > MAX1065BEUI+T (Maxim Integrated Products)IC ADC 14BIT 165KSPS 28TSSOP PDF资料下载
参数资料
| 型号： | MAX1065BEUI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/14页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 165KSPS 28TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 14 |
| 采样率（每秒）： | 165k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 16mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极 |
Reading the Conversion Result
EOC is provided to flag the microprocessor when a con-
version is complete. The falling edge of EOC signals
that the data is valid and ready to be output to the bus.
D0–D13 are the parallel outputs of the MAX1065/
MAX1066. These three-state outputs allow for direct
connection to a microcontroller I/O bus. The outputs
remain high-impedance during acquisition and conver-
sion. Data is loaded onto the bus with the third falling
edge of CS with R/C high after tDOns. Bringing CS high
forces the output bus back to high-impedance. The
MAX1065/MAX1066 then waits for the next falling edge
of CS to start the next conversion cycle (Figure 2).
The MAX1065 loads the conversion result onto a 14-bit-
wide data bus while the MAX1066 has a byte-wide out-
put format. HBEN toggles the output between the
most/least significant byte. The least significant byte is
loaded onto the output bus when HBEN is low and the
most significant byte is on the bus when HBEN is high
(Figure 2).
RESET
Toggle RESET with CS high. The next falling edge of
CS will begin acquisition. This reset is an alternative to
the dummy conversion explained in the
Starting a
Conversion section.
Transfer Function
Figure 8 shows the MAX1065/MAX1066 output transfer
function. The output is coded in standard binary.
Input Buffer
Most applications require an input buffer amplifier to
achieve 14-bit accuracy. If the input signal is multiplexed,
the input channel should be switched immediately after
acquisition, rather than near the end of or after a conver-
sion. This allows more time for the input buffer amplifier to
respond to a large step-change in input signal. The input
amplifier must have a high enough slew rate to complete
the required output voltage change before the beginning
of the acquisition time. At the beginning of acquisition, the
internal sampling capacitor array connects to AIN (the
amplifier output) causing some output disturbance.
Ensure that the sampled voltage has settled to within the
required limits before the end of the acquisition time. If
the frequency of interest is low, AIN can be bypassed
with a large enough capacitor to charge the internal sam-
pling capacitor with very little ripple. However, for AC use,
AIN must be driven by a wideband buffer (at least
10MHz), which must be stable with the ADC’s capacitive
load (in parallel with any AIN bypass capacitor used) and
also settle quickly. An example of this circuit using the
MAX4434 is given in Figure 9.
MAX1065/MAX1066
Low-Power, 14-Bit Analog-to-Digital Converters
with Parallel Interface
______________________________________________________________________________________
11
5V
68k
Ω
100k
Ω
150k
Ω
0.22
μF
REFADJ
MAX1065
MAX1066
Figure 7. MAX1065/MAX1066 Reference Adjust Circuit
ANALOG
INPUT
10
Ω
40pF
AIN
MAX1065/
MAX1066
MAX4434
Figure 9. MAX1065/MAX1066 Fast Settling Input Buffer
OUTPUT CODE
FULL-SCALE
TRANSITION
11...111
12
3
0
FS
FS - 3/2LSB
FS = VREF
INPUT VOLTAGE (LSB)
1LSB =
VREF
16384
11...110
11...101
00...011
00...010
00...001
00...000
Figure 8. MAX1065/MAX1066 Transfer Function
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484E18B11PB | CONN PLUG 11POS STRAIGHT W/PINS |
| MAX1247AEEE+T | IC ADC 12BIT SERIAL 16-QSOP |
| MS3106E28-21SZ | CONN PLUG 37POS STRAIGHT W/SCKT |
| MAX11048ECB+T | IC ADC 16BIT PAR 250KSPS 64TQFP |
| MS3106E28-21SY | CONN PLUG 37POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1065CCUI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1065CEUI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1066 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Power.14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1066ACUP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1066ACUP+ | 功能描述:模数转换器 - ADC Low-Power 14-Bit w/Parallel Interface RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。