- 您现在的位置：买卖IC网 > PDF目录9944 > MAX1072ETC+ (Maxim Integrated Products)IC ADC 10BIT 1.8MSPS 12-TQFN PDF资料下载
参数资料
| 型号： | MAX1072ETC+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/18页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 1.8MSPS 12-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 位数： | 10 |
| 采样率（每秒）： | 1.8M |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 45mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WQFN 裸露焊盘 |
| 供应商设备封装： | 12-TQFN-EP（4x4） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极 |
For continuous conversion, set the serial port to trans-
mit a clock, and pulse the frame sync signal for a clock
period before data transmission. The serial-port config-
uration (SPC) register should be set up with internal
frame sync (TXM = 1), CLKX driven by an on-chip clock
source (MCM = 1), burst mode (FSM = 1), and 16-bit
word length (FO = 0).
This setup allows continuous conversions provided that
the data transmit register (DXR) and the data-receive
register (DRR) are serviced before the next conversion.
Alternatively, autobuffering can be enabled when using
the buffered serial port to execute conversions and
read the data without CPU intervention. Connect the VL
pin to the TMS320C54_ supply voltage when the
MAX1072/MAX1075 are operating with an analog sup-
ply voltage higher than the DSP supply voltage. The
word length can be set to 8 bits with FO = 1 to imple-
ment the power-down modes. The CNVST pin must idle
high to remain in either power-down state.
Another method of connecting the MAX1072/MAX1075
to the TMS320C54_ is to generate the clock signals
external to either device. This connection is shown in
Figure 16 where serial clock (CLOCK) drives the CLKR
and SCLK and the convert signal (CONVERT) drives
the FSR and CNVST.
The serial port must be set up to accept an external
receive-clock and external receive-frame sync.
The SPC register should be written as follows:
TXM = 0, external frame sync
MCM = 0, CLKX is taken from the CLKX pin
FSM = 1, burst mode
FO = 0, data transmitted/received as 16-bit words
This setup allows continuous conversion, provided that
the DRR is serviced before the next conversion.
Alternatively, autobuffering can be enabled when using
the buffered serial port to read the data without CPU
intervention. Connect the VL pin to the TMS320C54_
supply voltage when the MAX1072/MAX1075 are oper-
ating with an analog supply voltage higher than the
DSP supply voltage.
The MAX1072/MAX1075 can also be connected to the
TMS320C54_ by using the data transmit (DX) pin to
drive CNVST and the CLKX generated internally to
drive SCLK. A pullup resistor is required on the CNVST
signal to keep it high when DX goes high impedance
and 0001hex should be written to the DXR continuously
for continuous conversions. The power-down modes
may be entered by writing 00FFhex to the DXR (see
Figures 17 and 18).
DSP Interface to the ADSP21_ _ _
The MAX1072/MAX1075 can be directly connected to
the ADSP21_ _ _ family of DSPs from Analog Devices,
Inc. Figure 19 shows the direct connection of the
MAX1072/MAX1075 to the ADSP21_ _ _. There are two
modes of operation that can be programmed to interface
with the MAX1072/MAX1075. For continuous conver-
sions, idle CNVST low and pulse it high for one clock
cycle during the LSB of the previous transmitted word.
The ADSP21_ _ _ STCTL and SRCTL registers should be
configured for early framing (LAFR = 0) and for an
active-high frame (LTFS = 0, LRFS = 0) signal. In this
mode, the data-independent frame-sync bit (DITFS = 1)
can be selected to eliminate the need for writing to the
transmit-data register more than once. For single conver-
sions, idle CNVST high and pulse it low for the entire
conversion. The ADSP21_ _ _ STCTL and SRCTL regis-
MAX1072/MAX1075
1.8Msps, Single-Supply, Low-Power,
True-Differential, 10-Bit ADCs
14
______________________________________________________________________________________
Figure 15. Interfacing to the TMS320C54_ Internal Clocks
Figure 16. Interfacing to the TMS320C54_ External Clocks
MAX1072
MAX1075
TMS320C54_
VL
SCLK
CNVST
DOUT
DVDD
CLKR
FSR
CLKX
FSX
DR
MAX1072
MAX1075
TMS320C54_
VL
DVDD
SCLK
CLKR
CNVST
FSR
DOUT
DR
CLOCK
CONVERT
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72T1865L5BBI | IC FIFO 8192X18 5NS 144BGA |
| MS27473T12B3PD | CONN PLUG 3POS STRAIGHT W/PINS |
| IDT72T1865L4-4BB | IC FIFO 8192X18 4NS 144BGA |
| V150B36M250B2 | CONVERTER MOD DC/DC 36V 250W |
| MAX1071ETC+ | IC ADC 10BIT 1.5MSPS 12-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1072ETC+ | 功能描述:模数转换器 - ADC 10Bit 1.8Msps Single Sply True Diff RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1072ETC+T | 功能描述:模数转换器 - ADC 10Bit 1.8Msps Single Sply True Diff RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1072ETC-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1075 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1.8Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1075CTC | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。