- 您现在的位置：买卖IC网 > PDF目录9749 > MAX1076CTC+T (Maxim Integrated Products)IC ADC 10BIT 1.8MSPS 12-TQFN PDF资料下载
参数资料
| 型号： | MAX1076CTC+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/18页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 1.8MSPS 12-TQFN |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 采样率（每秒）： | 1.8M |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 50mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WQFN 裸露焊盘 |
| 供应商设备封装： | 12-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极 |
Applications Information
Internal Reference
The MAX1076/MAX1078 have an on-chip voltage refer-
ence trimmed to 4.096V. The internal reference output
is connected to REF and also drives the internal capac-
itive DAC. The output can be used as a reference volt-
age source for other components and can source up to
2mA. Bypass REF with a 0.01F capacitor and a 4.7F
capacitor to RGND.
The internal reference is continuously powered up dur-
ing both normal and partial power-down modes. In full
power-down mode, the internal reference is disabled.
Be sure to allow at least 2ms recovery time after hard-
ware power-up or exiting full power-down mode for the
reference to reach its intended value.
How to Start a Conversion
An analog-to-digital conversion is initiated by CNVST
and clocked by SCLK, and the resulting data is clocked
out on DOUT by SCLK. With SCLK idling high or low, a
falling edge on CNVST begins a conversion. This causes
the analog input stage to transition from track to hold
mode, and DOUT to transition from high impedance to
being actively driven low. A total of 16 SCLK cycles are
required to complete a normal conversion. If CNVST is
low during the 16th falling SCLK edge, DOUT returns to
high impedance on the next rising edge of CNVST or
SCLK, enabling the serial interface to be shared by multi-
ple devices. If CNVST returns high after the 14th, but
before the 16th SCLK rising edge, DOUT remains active
so continuous conversions can be sustained. The high-
est throughput is achieved when performing continuous
conversions. Figure 10 illustrates a conversion using a
typical serial interface.
Connection to
Standard Interfaces
The MAX1076/MAX1078 serial interface is fully compati-
ble with SPI/QSPI and MICROWIRE (see Figure 11). If a
serial interface is available, set the CPU’s serial interface
in master mode so the CPU generates the serial clock.
Choose a clock frequency up to 28.8MHz.
SPI and MICROWIRE
When using SPI or MICROWIRE, the MAX1076/MAX1078
are compatible with all four modes programmed with the
CPHA and CPOL bits in the SPI or MICROWIRE control
register. Conversion begins with a CNVST falling edge.
DOUT goes low, indicating a conversion is in progress.
Two consecutive 1-byte reads are required to get the full
10 bits from the ADC. DOUT transitions on SCLK rising
edges. DOUT is guaranteed to be valid tDOUT later and
MAX1076/MAX1078
1.8Msps, Single-Supply, Low-Power, True-
Differential, 10-Bit ADCs with Internal Reference
______________________________________________________________________________________
11
OUTPUT CODE
FULL-SCALE
TRANSITION
FS
0
-FS
FS - 3/2 LSB
DIFFERENTIAL INPUT
VOLTAGE (LSB)
011...111
011...110
000...010
000...001
000...000
111...111
111...110
111...101
100...001
100...000
1 LSB =
VREF
1024
FS =
VREF
2
- FS =
-VREF
2
ZS = 0
Figure 8. Unipolar Transfer Function (MAX1076 Only)
OUTPUT CODE
FULL-SCALE
TRANSITION
FS
0
-FS
FS - 3/2 LSB
DIFFERENTIAL INPUT
VOLTAGE (LSB)
011...111
011...110
000...010
000...001
000...000
111...111
111...110
111...101
100...001
100...000
1 LSB =
VREF
1024
FS =
VREF
2
- FS =
-VREF
2
ZS = 0
Figure 9. Bipolar Transfer Function (MAX1078 Only)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2TM-MX-F3 | CONVERTER MOD DC/DC 10V 75W |
| VI-2TM-MX-F2 | CONVERTER MOD DC/DC 10V 75W |
| VI-2TM-MX-F1 | CONVERTER MOD DC/DC 10V 75W |
| MS27466E21A16PA | CONN RCPT 16POS WALL MT W/PINS |
| D38999/24JB98JN | CONN RCPT 6POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1076ETC | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1076ETC+ | 功能描述:模数转换器 - ADC 10Bit 1.8Msps Single Sply True Diff RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1076ETC+T | 功能描述:模数转换器 - ADC 10Bit 1.8Msps Single Sply True Diff RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1076ETC-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1077 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs with Internal Reference |
发布紧急采购，3分钟左右您将得到回复。