- 您现在的位置：买卖IC网 > PDF目录9942 > MAX1085BCSA+T (Maxim Integrated Products)IC ADC 10BIT 300KSPS 8-SOIC PDF资料下载
参数资料
| 型号： | MAX1085BCSA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 300KSPS 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 采样率（每秒）： | 300k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 471mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极 |
MAX1084/MAX1085
400ksps/300ksps, Single-Supply, Low-Power,
Serial 10-Bit ADCs with Internal Reference
_______________________________________________________________________________________
9
DAC, which in turn forms a digital representation of the
analog input signal. At the conversion’s end, the input
side of CHOLD switches back to AIN, and CHOLD
charges to the input signal again.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the maximum time the device takes to acquire
the signal and the minimum time needed for the signal
to be acquired. Acquisition time is calculated by:
tACQ = 7(RS + RIN) 12pF
where RIN = 800, RS = the input signal’s source
impedance, and tACQ is never less than 468ns
(MAX1284) or 625ns (MAX1085). Source impedance
below 4k
does not significantly affect the ADC’s AC
performance.
Higher source impedances can be used if a 0.01F
capacitor is connected to the analog input. Note that
the input capacitor forms an RC filter with the input
source impedance, limiting the ADC’s input signal
bandwidth.
Input Bandwidth
The ADC’s input tracking circuitry has a 6MHz
(MAX1084) or 3MHz (MAX1085) small-signal band-
width, so it is possible to digitize high-speed transient
events and measure periodic signals with bandwidths
exceeding the ADC’s sampling rate by using under-
sampling techniques. To avoid aliasing of unwanted
high-frequency signals into the frequency band of inter-
est, anti-alias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog
input to VDD and GND, allow the input to swing from
(GND - 0.3V) to (VDD + 0.3V) without damage.
If the analog input exceeds 50mV beyond the supplies,
limit the input current to 2mA.
Internal Reference
The MAX1084/MAX1085 have an on-chip voltage refer-
ence trimmed to 2.5V. The internal reference output is
connected to REF and also drives the internal capacitive
DAC. The output can be used as a reference voltage
source for other components and can source up to
800A. Bypass REF with a 4.7F capacitor. Larger
capacitors increase wake-up time when exiting shut-
down (see Using SHDN to Reduce Supply Current). The
internal reference is disabled in shutdown (SHDN = 0).
Serial Interface
Initialization After Power-Up and
Starting a Conversion
When power is first applied, and if SHDN is not pulled
low, it takes the fully discharged 4.7F reference
bypass capacitor up to 1.4ms to acquire adequate
charge for specified accuracy. No conversions should
be performed during this time.
CHOLD
12pF
RIN
800
HOLD
CSWITCH*
6pF
*INCLUDES ALL INPUT PARASITICS
AIN
REF
GND
ZERO
AUTOZERO
RAIL
COMPARATOR
CAPACITIVE DAC
TRACK
SHUTDOWN
INPUT
ANALOG INPUT
0 TO VREF
+3V to +5V
1
2
3
4
VDD
AIN
SHDN
REF
8
7
6
5
SCLK
CS
DOUT
GND
SERIAL
INTERFACE
4.7
F
10
F 0.1F
MAX1084
MAX1085
Figure 3. Typical Operating Circuit
Figure 4. Equivalent Input Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MS27466T25B35SA | CONN RCPT 128POS WALL MNT W/SCKT |
| MS27466E25B35SA | CONN RCPT 128POS WALL MNT W/SCKT |
| MS27499E10F35PB | CONN RCPT 13POS BOX MNT W/PINS |
| IDT723651L15PQF | IC FIFO SYNC 2048X36 132QFP |
| MS27467T23B53PD | CONN PLUG 53POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1085BESA | 功能描述:模数转换器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1085BESA+ | 功能描述:模数转换器 - ADC 300/400ksps Sgl-Sply 4Ch Serial 10Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1085BESA+T | 功能描述:模数转换器 - ADC 300/400ksps Sgl-Sply 4Ch Serial 10Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1085BESA-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1086 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:150ksps, 10-Bit, 2-Channel Single-Ended, and 1-Channel True-Differential ADCs in SOT23 |
发布紧急采购，3分钟左右您将得到回复。