- 您现在的位置：买卖IC网 > PDF目录9882 > MAX11048ETN+T (Maxim Integrated Products)IC ADC 16BIT 250KSPS SAR 56TQFN PDF资料下载
参数资料
| 型号： | MAX11048ETN+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/25页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 250KSPS SAR 56TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 并联 |
| 转换器数目： | 6 |
| 功率耗散（最大）： | 3.81W |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 6 个单端，单极 |
MAX11047–MAX11049/MAX11057–MAX11059
4-/6-/8-Channel, 16-/14-Bit,
Simultaneous-Sampling ADCs
16
______________________________________________________________________________________
Figures 2 and 3 illustrate the clamp circuit voltage-cur-
rent characteristics for a source impedance RS =
1280
. While the input voltage is within the -300mV to
+(VAVDD + 300mV) range, no current flows in the input
clamps. Once the input voltage goes beyond this volt-
age range, the clamps turn on and limit the voltage at
the input pin.
Applications Information
Digital Interface
The bidirectional, parallel, digital interface, CR0–CR3,
sets the 4-bit configuration register. This interface
configures the following control signals: chip select
(CS), read (RD), write (WR), end of conversion (EOC),
and convert start (CONVST). Figures 6 and 7 and the
Timing Characteristics in the
Electrical Characteristics
table show the operation of the interface.
DB0–DB15/13, output the 16-/14-bit conversion result.
All bits are high impedance when RD = 1 or CS = 1.
CR3 (Int/Ext Reference)
CR3 selects the internal or external reference. The POR
default = 0.
0 = internal reference, REFIO internally driven through a
10k
resistor, bypass with 0.1F capacitor to AGND.
1 = external reference, drive REFIO with a high quality
reference.
CR2 (Output Data Format)
CR2 selects the output data format. The POR default = 0.
0 = offset binary.
1 = two’s complement.
CR1 (Reserved)
CR1 must be set to 0.
CR0 (CONVST Mode)
CR0 selects the acquisition mode. The POR default = 0.
0 = CONVST controls the acquisition and conversion.
Drive CONVST low to start acquisition. The rising edge
of CONVST begins the conversion.
1 = acquisition mode starts as soon as previous con-
version is complete. The rising edge of CONVST begins
the conversion.
Programming the Configuration Register
To program the configuration register, bring the CS and
WR low and apply the required configuration data on
CR3–CR0 of the bus and then raise WR once to save
changes.
CAUTION: The host driving CR3–CR0 must relin-
quish the bus when the conversion results of the
ADC are being read.
Starting a Conversion
CONVST initiates conversions. The devices provide two
acquisition modes set through the configuration regis-
ter. Allow a quiet time (tQ) of 500ns prior to the start of
conversion to avoid any noise interference during read-
out or write operations from corrupting a sample.
CR3
CR2
CR1
CR0
Int/Ext
Reference
Output
Data Format
Must be set
to 0
CONVST
Mode
Table 1. Configuration Register
SIGNAL VOLTAGE AT SOURCE AND CH_ INPUT (V)
I CLAMP
(mA)
30
20
0
10
-10
-20
-15
-10
-5
0
5
10
15
20
25
-25
-30
40
RS = 1170
I
VAVDD = 5.0V
AT SOURCE
AT CH_ INPUT
Figure 2. Input Clamp Characteristics
SIGNAL VOLTAGE AT SOURCE AND CH_ INPUT (V)
6
4
2
0
-2
-4
8
I CLAMP
(mA)
-20
-15
-10
-5
10
15
20
25
-25
0
5
RS = 1170
I
VAVDD = 5.0V
AT CH_ INPUT
AT SOURCE
Figure 3. Input Clamp Characteristics (Zoom In)
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106E28-21SX | CONN PLUG 37POS STRAIGHT W/SCKT |
| MS3106E28-21SW | CONN PLUG 37POS STRAIGHT W/SCKT |
| MAX158BCWI+T | IC ADC 8BIT 8CH W/MUX&REF 28SOIC |
| MS3100F20-27P | CONN RCPT 14POS WALL MNT W/PINS |
| MS27499E24B61SA | CONN RCPT 61POS BOX MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11049 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs |
| MAX11049ECB+ | 功能描述:模数转换器 - ADC 16Bit 8Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11049ECB+T | 功能描述:模数转换器 - ADC 16Bit 8Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11049ETN+ | 功能描述:模数转换器 - ADC 16Bit 8Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11049ETN+T | 功能描述:模数转换器 - ADC 16Bit 8Ch Simult Sampling RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。