- 您现在的位置：买卖IC网 > PDF目录9880 > MAX11060GUU+ (Maxim Integrated Products)IC ADC 16BIT DELTA SIGMA 38TSSOP PDF资料下载
参数资料
| 型号： | MAX11060GUU+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/35页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT DELTA SIGMA 38TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 3.07M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 4 |
| 功率耗散（最大）： | 1.1W |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 106°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 8 个单端，双极；4 个差分，双极 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
MAX11040K/MAX11060
24-/16-Bit, 4-Channel, Simultaneous-Sampling,
Cascadable, Sigma-Delta ADCs
10
Maxim Integrated
Pin Description (continued)
PIN
NAME
FUNCTION
11, 28
DGND
Digital Ground
12, 27
DVDD
Positive Digital Supply Voltage. Bypass each DVDD to DGND with a 1μF capacitor in parallel with a
0.01μF capacitor as close as possible to the device.
13
CASCIN
Cascade Input. A logic-low on CASCIN while CS is a logic-low during the last cycle of a byte signals the
device to perform the requested data transfer during subsequent bytes using DIN and DOUT. Once the
requested transfer is completed, the part three-states DOUT and ignores DIN until a new command is
issued. CASCIN is clocked in at the rising edge of SCLK. Connect CASCIN to DGND when not daisy
chaining multiple devices. See the Multiple Device Connection section for connection recommendations.
14
CASCOUT
Cascade Output. CASCOUT is driven low during the last cycle of the last byte of a data transfer to signal
the next device in the daisy-chain to begin transferring data on the next byte. CASCOUT changes after
the rising edge of SCLK. Leave CASCOUT unconnected when not daisy chaining multiple devices. See
the Multiple Device Connection section.
15
CS
Active-Low Chip-Select Input. A falling edge on CS while CASCIN is a logic-low enables DIN and DOUT
for data transfer. A logic-high on CS prevents data from being clocked in on DIN and places DOUT in a
high-impedance state.
16
SCLK
Serial-Clock Input. Clocks in data at DIN on the falling edge of SCLK and clocks out data at DOUT on the
rising edge of SCLK. SCLK must idle high (CPOL = 1).
17
DIN
Serial Data Input. Data at DIN is clocked in on the falling edge of SCLK.
18
DOUT
Serial Data Output. The drive for DOUT is enabled by a falling edge on CS while CASCIN is low or by a
falling edge on CASCIN while CS is low. DOUT is disabled/three-stated when CS is high or after the
appropriate number of data bytes have been transferred in response to the requested command. Data is
clocked out at DOUT on the rising edge of SCLK.
19
FAULT
Active-Low Overvoltage Fault Indicator Output. FAULT goes low when any analog input goes outside the fault
threshold range (between VPFT and VNFT). The FAULT output is open drain with a 30k
Ω internal pullup
resistor, allowing wire-NOR functionality. See the Analog Input Overvoltage and Fault Protection section.
20
OVRFLW
Active-Low Channel Data Overflow Output. OVRFLW goes low when a conversion result goes outside the
voltage range bounded by the positive and negative full scale on one or more of the analog input
channels or when FAULT goes low. The OVRFLW output is open drain with a 30k
Ω internal pullup resistor,
allowing wire-NOR functionality. See the Analog Input Overvoltage and Fault Protection section.
21
CLKOUT
Buffered Clock Output. When the XTALEN bit in the configuration register is 1 and a crystal is installed
between XIN and XOUT, CLKOUT provides a buffered version of the internal oscillator’s clock. Setting the
XTALEN bit to 0 places CLKOUT in a high-impedance state.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T21A35S | CONN RCPT 79POS JAM NUT W/SCKT |
| MS27497T16F26PA | CONN RCPT 26POS WALL MNT W/PINS |
| VI-BWF-MW-F3 | CONVERTER MOD DC/DC 72V 100W |
| V300A28T500B3 | CONVERTER MOD DC/DC 28V 500W |
| MAX1062CCUB+ | IC ADC 14BIT 200KSPS 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11060GUU+ | 功能描述:模数转换器 - ADC 24/16Bit 4Ch Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11060GUU+T | 功能描述:模数转换器 - ADC 24/16Bit 4Ch Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11068EVKIT | 功能描述:电源管理IC开发工具 Programmers, Development Systems Eval and Demo Boards and Kits - KIT SMART BATT MEASUREMENT 12CH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX11068EVKIT+ | 功能描述:电源管理IC开发工具 Programmers, Development Systems Eval and Demo Boards and Kits - KIT SMART BATT MEASUREMENT 12CH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX11068EVMINIQU+ | 功能描述:电池管理 Automotive Battery Sensor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。