- 您现在的位置：买卖IC网 > PDF目录17008 > MAX11103EVKIT+ (Maxim Integrated Products)KIT EVALUATION FOR MAX11103 PDF资料下载
参数资料
| 型号： | MAX11103EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/30页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR MAX11103 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
23
Maxim Integrated
2Msps/3Msps, Low-Power,
Serial 12-/10-/8-Bit ADCs
MAX11102/03/05/06/10/11/15/16/17
To sustain the maximum sample rate, all devices have to
be resampled immediately after the 16th clock cycle. For
lower sample rates, the CS falling edge can be delayed
leaving DOUT in a high-impedance condition. Pull CS
high after the 10th SCLK falling edge (see the Operating
Modes section).
Analog Input
The devices produce a digital output that corresponds to
the analog input voltage within the specified operating
range of 0 to VREF for the dual-channel devices and 0 to
VDD for the single-channel devices.
Figure 6 shows an equivalent circuit for the analog input
AIN (for single-channel devices) and AIN1/AIN2 (for
dual-channel devices). Internal protection diodes D1/D2
confine the analog input voltage within the power rails
(VDD, GND). The analog input voltage can swing from
GND - 0.3V to VDD + 0.3V without damaging the device.
The electric load presented to the external stage driv-
ing the analog input varies depending on which mode
the ADC is in: track mode vs. conversion mode. In track
mode, the internal sampling capacitor CS (16pF) has to
be charged through the resistor R (R = 50I) to the input
voltage. For faithful sampling of the input, the capacitor
voltage on CS has to settle to the required accuracy dur-
ing the track time.
The source impedance of the external driving stage in
conjunction with the sampling switch resistance affects
the settling performance. The THD vs. Input Resistance
graph in the Typical Operating Characteristics shows
THD sensitivity as a function of the signal source imped-
ance. Keep the source impedance at a minimum for
high-dynamic performance applications. Use a high-
performance op amp such as the MAX4430 to drive the
analog input, thereby decoupling the signal source and
the ADC.
While the ADC is in conversion mode, the sampling
switch is open presenting a pin capacitance, CP (CP
= 5pF), to the driving stage. See the Applications
Information section for information on choosing an
appropriate buffer for the ADC.
ADC Transfer Function
The output format is straight binary. The code transi-
tions midway between successive integer LSB values
such as 0.5 LSB, 1.5 LSB, etc. The LSB size for single-
channel devices is VDD/2n and for dual-channel devices
is VREF/2n, where n is the resolution. The ideal transfer
characteristic is shown in Figure 10.
Operating Modes
The ICs offer two modes of operation: normal mode and
power-down mode. The logic state of the CS signal
during a conversion activates these modes. The power-
down mode can be used to optimize power dissipation
with respect to sample rate.
Normal Mode
In normal mode, the devices are powered up at all times,
thereby achieving their maximum throughput rates.
Figure 7 shows the timing diagram of these devices in
normal mode. The falling edge of CS samples the analog
input signal, starts a conversion, and frames the serial
data transfer.
Figure 6. Analog Input Circuit
Figure 7. Normal Mode
CP
AIN1/AIN2
VDD
AIN
D2
D1
R
CS
SWITCH CLOSED IN TRACK MODE
SWITCH OPEN IN CONVERSION MODE
12345678
910111213141516
SCLK
PULL CS HIGH AFTER THE 10TH SCLK FALLING EDGE
KEEP CS LOW UNTIL AFTER THE 10TH SCLK FALLING EDGE
CS
DOUT
VALID DATA
HIGH
IMPEDANCE
HIGH
IMPEDANCE
相关PDF资料 |
PDF描述 |
|---|---|
| GEC30DRYI-S13 | CONN EDGECARD 60POS .100 EXTEND |
| RCM18DCBN | CONN EDGECARD 36POS R/A .156 SLD |
| VI-2WD-EY | CONVERTER MOD DC/DC 85V 50W |
| RBC15DREI-S13 | CONN EDGECARD 30POS .100 EXTEND |
| RCM18DCCD | CONN EDGECARD 36POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11103EVKIT+ | 功能描述:数据转换 IC 开发工具 MAX11103 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX11105 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2Msps/3Msps, Low-Power, Serial 12-/10-/8-Bit ADCs |
| MAX11105AUT+ | 制造商:Maxim Integrated Products 功能描述:SMALL, 2.2V TO 3.6V, LOW-POWER, 1-/2-CHANNEL, SERIAL, 8-/10- - Rail/Tube |
| MAX11105AUT+T | 功能描述:模数转换器 - ADC 12Bit 1Ch 2Msps Serial RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11105AUT+TCBG | 功能描述:模数转换器 - ADC SEL customer special of the MAX11105AUT+T RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。