参数资料
| 型号： | MAX1112CPP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT LP 20-DIP |
| 标准包装： | 18 |
| 位数： | 8 |
| 采样率（每秒）： | 50k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 680µW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 8 个单端，单极；8 个单端，双极；4 个伪差分，单极；4 个伪差分，双极 |
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
14
______________________________________________________________________________________
SSTRB
CS
SCLK
DIN
DOUT
14
8
12
15
17
START
SEL2 SEL1 SEL0
UNI/
BIP
SGL/
DIF
PD1
PD0
B7
B6
B1
B0
tACQ
4s (fSCLK = 500kHz)
IDLE
FILLED WITH
ZEROS
IDLE
CONVERSION
25s TYP
A/D STATE
2
3
5
6
7
9
10
11
16
18
tCONV
Figure 10. Internal Clock Mode Timing
PD0 CLOCK IN
tSSTRB
tCSH
tCONV
tSCK
SSTRB
SCLK
tCSS
NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION.
CS
Figure 11. Internal Clock Mode SSTRB Detailed Timing
Internal Clock
Internal clock mode frees the P from the burden of
running the SAR conversion clock. This allows the con-
version results to be read back at the processor’s con-
venience, at any clock rate up to 2MHz. SSTRB goes
low at the start of the conversion and then goes high
when the conversion is complete. SSTRB is low for
25s (typ), during which time SCLK should remain low
for best noise performance.
An internal register stores data when the conversion is
in progress. SCLK clocks the data out of this register at
any time after the conversion is complete. After SSTRB
goes high, the second falling clock edge produces the
MSB of the conversion at DOUT, followed by the
remaining bits in MSB-first format (Figure 10). CS does
not need to be held low once a conversion is started.
Pulling CS high prevents data from being clocked into
the MAX1112/MAX1113 and three-states DOUT, but it
does not adversely affect an internal clock-mode con-
version already in progress. When internal clock mode
is selected, SSTRB does not go into a high-impedance
state when CS goes high.
Figure 11 shows the SSTRB timing in internal clock
mode. In this mode, data can be shifted in and out of
the MAX1112/MAX1113 at clock rates up to 2MHz, pro-
vided that the minimum acquisition time, tACQ, is kept
above 1s.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27474T22B21SC | CONN RCPT 21POS JAM NUT W/SCKT |
| MAX1110EPP+ | IC ADC 8BIT LP 20-DIP |
| MS27468T23A35SB | CONN RCPT 100POS JAM NUT W/SCKT |
| MS3100F20-14S | CONN RCPT 5POS WALL MNT W/SCKT |
| MAX3480AEPI+ | IC RS485/RS422 DATA INTRFC 28DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1112CPP+ | 功能描述:模数转换器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1112D | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs Internal 4.096V Reference |
| MAX1112EAP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1112EAP+ | 功能描述:模数转换器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1112EAP+T | 功能描述:模数转换器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。