- 您现在的位置：买卖IC网 > PDF目录9844 > MAX1132BCAP+T (Maxim Integrated Products)IC ADC 16BIT 200KSPS 20-SSOP PDF资料下载
参数资料
| 型号： | MAX1132BCAP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/19页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 200KSPS 20-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 位数： | 16 |
| 采样率（每秒）： | 200k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 55mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
the beginning of calibration and goes high to signal the
end of calibration, approximately 80,000 clock cycles
later. In external clock mode, SSTRB goes high at the
beginning of calibration and goes low to signal the end
of calibration. Calibration should be performed in the
same clock mode as will be used for conversions.
Reference
The MAX1132/MAX1133 can be used with an internal
or external reference. An external reference can be
connected directly at the REF pin or at the REFADJ pin.
CREF is an internal reference node and must be
bypassed with a 1F capacitor when using either the
internal or an external reference.
Internal Reference
When using the MAX1132/MAX1133’s internal refer-
ence, place a 0.22F ceramic capacitor from REFADJ
to AGND and place a 2.2F capacitor from REF to
AGND. Fine adjustments can be made to the internal
reference voltage by sinking or sourcing current at
REFADJ. The input impedance of REFADJ is nominally
9k. The internal reference voltage is adjustable to
±1.5% with the circuit of Figure 7.
External reference
An external reference can be placed at either the input
(REFADJ) or the output (REF) of the MAX1132/
MAX1133’s internal buffer amplifier.
When connecting an external reference to REFADJ, the
input impedance is typically 9k. Using the buffered
REFADJ input makes buffering of the external reference
unnecessary, however, the internal buffer output must
be bypassed at REF with a 2.2F capacitor.
When connecting an external reference at REF,
REFADJ must be connected to AVDD. Then the input
impedance at REF is a minimum of 164k for DC cur-
rents. During conversion, an external reference at REF
must deliver 250A DC load current and have an out-
put impedance of 10 or less. If the reference has a
higher output impedance or is noisy, bypass it at the
REF pin with a 4.7F capacitor.
Analog Input
The MAX1132/MAX1133 use a capacitive DAC that
provides an inherent track/hold function. Drive AIN with
a source impedance less than 10. Any signal condi-
tioning circuitry must settle with 16-bit accuracy in less
than 500ns. Limit the input bandwidth to less than half
the sampling frequency to eliminate aliasing. The
MAX1132/MAX1133 has a complex input impedance
which varies from unipolar to bipolar mode (Figure 1).
Input Range
The analog input range in unipolar mode is 0 to +12V
for the MAX1132, and 0 to +4.096V for the MAX1133. In
bipolar mode, the analog input can be -12V to +12V for
the MAX1132, and -4.096V to +4.096V for the
MAX1133. Unipolar and bipolar mode is programmed
with the UNI/
BIP bit of the Control Byte. When using a
reference other than the MAX1132/MAX1133’s internal
+4.096V reference, the full-scale input range will vary
accordingly. The full-scale input range depends on the
voltage at REF and the sampling mode selected (Tables
3 and 4).
Input Acquisition and Settling
Clocking in a Control Byte starts input acquisition. In
bipolar mode the main capacitor array starts acquiring
the input as soon as a start bit is recognized. If unipolar
mode is selected by the second DIN bit, the part will
immediately switch to unipolar sampling mode and
acquire a sample.
Acquisition can be extended by eight clock cycles by
setting M1 = 1, M0 = 1 (long acquisition mode). The
sampling instant in short acquisition completes on the
falling edge of the sixth clock cycle after the start bit
(Figure 2).
Acquisition is 5.5 clock cycles in short acquisition
mode and 13.5 clock cycles in long acquisition mode.
Short acquisition mode is 24 clock cycles per conver-
sion. Using the external clock to run the conversion
process limits unipolar conversion speed to 125ksps
instead of 200ksps in bipolar mode. The input resis-
tance in unipolar mode is larger than that of bipolar
mode (Figure1). The RC time constant in unipolar mode
is larger than that of bipolar mode, reducing the maxi-
mum conversion rate in 24 external clock mode. Long
acquisition mode with external clock allows both unipo-
lar and bipolar sampling of 150ksps (4.8MHz/32 clock
cycles) by adding eight extra clock cycles to the con-
version.
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
______________________________________________________________________________________
13
+5V
510k
100k
24k
0.22F
REFADJ
MAX1132
Figure 7. MAX1132 Reference-Adjust Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26FB5PC | CONN PLUG 5POS STRAIGHT W/PINS |
| MAX3221ECAE+T | IC TXRX RS-232 W/SHTDWN 16SSOP |
| MX574AJP+ | IC ADC 12BIT W/REF 28-PLCC |
| MAX1158BEUP+ | IC ADC 14BIT 135KSPS 20-TSSOP |
| V28C24M100BF2 | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1132BEAP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1132BEAP+ | 功能描述:模数转换器 - ADC 16-Bit 200ksps 5V Single-Supply w/Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1132BEAP+T | 功能描述:模数转换器 - ADC 16-Bit 200ksps 5V Single-Supply w/Ref RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1132BEAP-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1132EVC16 | 功能描述:数据转换 IC 开发工具 16-Bit 200ksps 5V Single-Supply w/Ref RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。