- 您现在的位置：买卖IC网 > PDF目录9959 > MAX1136EUA+T (Maxim Integrated Products)IC ADC 10BIT SERIAL 8-UMAX PDF资料下载
参数资料
| 型号： | MAX1136EUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/22页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT SERIAL 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 采样率（每秒）： | 94.4k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 3.35mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，单极；2 个差分，双极 |
External Clock
When configured for external clock mode (CLK = 1),
the MAX1136–MAX1139 use the SCL as the conversion
clock. In external clock mode, the MAX1136–MAX1139
begin tracking the analog input on the ninth rising clock
edge of a valid slave address byte. Two SCL clock
cycles later the analog signal is acquired and the con-
version begins. Unlike internal clock mode, converted
data is available immediately after the first four empty
high bits. The device will continuously convert input
channels dictated by the scan mode until given a not
acknowledge. There is no need to re-address the
device with a read command to obtain new conversion
results (see Figure 11).
The conversion must complete in 1ms or droop on the
track-and-hold capacitor will degrade conversion
results. Use internal clock mode if the SCL clock period
exceeds 60s.
The MAX1136–MAX1139 must operate in external clock
mode for conversion rates from 40ksps to 94.4ksps.
Below 40ksps internal clock mode is recommended
due to much smaller power consumption.
Scan Mode
SCAN0 and SCAN1 of the configuration byte set the
scan mode configuration. Table 5 shows the scanning
configurations. If AIN_/REF is set to be a reference
input or output (SEL1 = 1, Table 6), AIN_/REF will be
excluded from a multichannel scan. The scanned
results are written to memory in the same order as the
conversion. Read the results from memory in the order
they were converted. Each result needs a 2-byte trans-
mission, the first byte begins with six empty bits during
which SDA is left high. Each byte has to be acknowl-
edged by the master or the memory transmission will
be terminated. It is not possible to read the memory
independently of conversion.
Applications Information
Power-On Reset
The configuration and setup registers (Tables 1 and 2)
will default to a single-ended, unipolar, single-channel
conversion on AIN0 using the internal clock with VDD as
the reference and AIN_/REF configured as an analog
input. The memory contents are unknown after power-up.
Automatic Shutdown
Automatic shutdown occurs between conversions when
the MAX1136–MAX1139 are idle. All analog circuits
participate in automatic shutdown except the internal
reference due to its prohibitively long wake-up time.
When operating in external clock mode, a STOP, not-
acknowledge or repeated START, condition must be
issued to place the devices in idle mode and benefit
from automatic shutdown. A STOP condition is not nec-
essary in internal clock mode to benefit from automatic
shutdown because power-down occurs once all con-
version results are written to memory (Figure 10). When
using an external reference or VDD as a reference, all
analog circuitry is inactive in shutdown and supply cur-
rent is less than 0.5A (typ). The digital conversion
results obtained in internal clock mode are maintained
in memory during shutdown and are available for
access through the serial interface at any time prior to a
STOP or a repeated START condition.
When idle the MAX1136–MAX1139 continuously wait
for a START condition followed by their slave address
(see
Slave Address section). Upon reading a valid
address byte the MAX1136–MAX1139 power-up. The
internal reference requires 10ms to wake up, so when
using the internal reference it should be powered up
MAX1136–MAX1139
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
4-/12-Channel, 2-Wire Serial 10-Bit ADCs
______________________________________________________________________________________
17
SCAN1
SCAN0
SCANNING CONFIGURATION
00
Scans up from AIN0 to the input selected by CS3–CS0. When CS3–CS0 exceeds 1011, the scanning will
stop at AIN11. When AIN_/REF is set to be a reference input/output, scanning will stop at AIN2 and AIN10.
0
1
*Converts the input selected by CS3–CS0 eight times. (See Tables 3 and 4)
Scans up from AIN2 to the input selected by CS1 and CS0. When CS1 and CS0 are set for AIN0–AIN2,
the only scan that takes place is AIN2 (MAX1136/MAX1137). When AIN/REF is set to be a reference
input/output, scanning stops at AIN2.
10
Scans up from AIN6 to the input selected by CS3–CS0. When CS3–CS0 is set for AIN0–AIN6, the only
scan that takes place is AIN6 (MAX1138/MAX1139). When AIN/REF is set to be a reference input/
output, scanning stops at selected channel or AIN10.
1
*Converts channel selected by CS3–CS0.
*
When operating in external clock mode there is no difference between SCAN[1:0] = 01 and SCAN[1:0] = 11 and converting will occur
perpetually until not acknowledge occurs.
Table 5. Scanning Configuration
相关PDF资料 |
PDF描述 |
|---|---|
| VE-21H-MX-F3 | CONVERTER MOD DC/DC 52V 75W |
| VI-26M-IW-F1 | CONVERTER MOD DC/DC 10V 100W |
| MS27508E8F98S | CONN RCPT 3POS BOX MNT W/SCKT |
| VI-26K-IW-F3 | CONVERTER MOD DC/DC 40V 100W |
| VE-21H-MX-F2 | CONVERTER MOD DC/DC 52V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1136KEUA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1136KEUA-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1136LEUA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1136LEUA-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1136MEUA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。