- 您现在的位置：买卖IC网 > PDF目录9851 > MAX1145BEAP+T (Maxim Integrated Products)IC ADC 14BIT 150KSPS 20-SSOP PDF资料下载
参数资料
| 型号： | MAX1145BEAP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/18页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 150KSPS 20-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 位数： | 14 |
| 采样率（每秒）： | 150k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 26.4mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
range is 0 to +2.048V (unipolar) or
±2.048V (bipolar).
Unipolar and bipolar mode selection is configured with
bit 6 of the serial control byte (Table 1).
Figure 1 shows the equivalent input circuit of the
MAX1144/MAX1145. The resistor network on the analog
input provides
±16.5V fault protection. This circuit limits
the current going into or out of the pin to less than 2mA.
The overvoltage protection is active even if the device
is in a power-down mode, or if AVDD = 0.
Digital Interface
The digital interface pins consist of SHDN, RST, SSTRB,
DOUT, SCLK, DIN, and CS. Bringing SHDN low places
the MAX1144/MAX1145 in its 1.2A shutdown mode. A
logic low on RST halts the MAX1144/MAX1145 opera-
tion and returns the part to its power-on-reset state.
In external clock mode, SSTRB is low and pulses high
for one clock cycle at the start of conversion. In internal
clock mode, SSTRB goes low at the start of the conver-
sion, and goes high to indicate that the conversion is
finished.
The DIN input accepts control byte data, which is
clocked in on each rising edge of SCLK. After CS goes
low or after a conversion or calibration completes, the
first logic “1” clocked into DIN is interpreted as the
START bit, the MSB of the 8-bit control byte.
The SCLK input is the serial-data-transfer clock which
clocks data in and out of the MAX1144/MAX1145.
SCLK also drives the ADC conversion steps in external
clock mode (see the Internal and External Clock Modes
section).
DOUT is the serial output of the conversion result.
DOUT is updated on the falling edge of SCLK. DOUT is
high impedance when CS is high.
CS must be low for the MAX1144/MAX1145 to accept a
control byte. The serial interface is disabled when CS is
high.
User-Programmable Outputs
The MAX1144/MAX1145 have three user-programma-
ble outputs: P0, P1, and P2. The power-on default state
for the programmable outputs is zero. These are push-
pull CMOS outputs suitable for driving a multiplexer, a
PGA or other signal preconditioning circuitry. Bits 0, 1,
and 2 of the control byte control the user-programma-
ble outputs (Tables 1, 2).
MAX1144/MAX1145
14-Bit ADCs, 150ksps, 3.3V Single Supply
_______________________________________________________________________________________
9
ACQUISITION
CONVERSION
IDLE
SCLK
DOUT
A/D
STATE
DIN
SSTRB
CS
4
18
12
START
M1
M0
P2
P1
P0
15
21
24
B10
B9
B12
B11
B8
B7
B2
B13
MSB
B0
LSB
FILLED WITH
ZEROS
B1
X
tACQ
UNI/
BIP
INT/
EXT
Figure 2. Short Acquisition Mode (24 Clock Cycles) External Clock
OUTPUT PIN
PROGRAMMED
THROUGH CONTROL
BYTE
POWER-ON OR
RST DEFAULT
DESCRIPTION
P2
Bit 2
0
P1
Bit 1
0
P0
Bit 0
0
User-programmable outputs follow the state of the control
byte’s three LSBs, and are updated simultaneously when a
new control byte is written. Outputs are push-pull. In hardware
and software shutdown, these outputs are unchanged and
remain low impedance.
Table 2. User-Programmable Outputs
相关PDF资料 |
PDF描述 |
|---|---|
| MAX13485EELA+T | IC TXRX RS485/RS422 8-UDFN |
| VI-JNX-MX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
| VI-JNW-MX-F3 | CONVERTER MOD DC/DC 5.5V 75W |
| VI-JNW-MX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| VI-JNV-MX-F4 | CONVERTER MOD DC/DC 5.8V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1146 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Multichannel, True-Differential, Serial, 14-Bit ADCs |
| MAX1146BCUP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1146BCUP+ | 功能描述:模数转换器 - ADC 14-Bit 4Ch 116ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1146BCUP+T | 功能描述:模数转换器 - ADC 14-Bit 4Ch 116ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1146BCUP-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。