- 您现在的位置：买卖IC网 > PDF目录383310 > MAX1151BIZS (MAXIM INTEGRATED PRODUCTS INC) 8-Bit, 750Msps Flash ADC PDF资料下载
参数资料
| 型号： | MAX1151BIZS |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | ADC |
| 英文描述： | 8-Bit, 750Msps Flash ADC |
| 中文描述： | 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, PQFP80 |
| 封装： | MQUAD-80 |
| 文件页数： | 5/8页 |
| 文件大小： | 78K |
| 代理商： | MAX1151BIZS |
The MAX1151 has true differential analog and digital
data paths from the preamplifiers to the output buffers
(current-mode logic) for reducing potential missing
codes while rejecting common-mode noise.
Signature errors are also reduced by careful layout of the
analog circuitry. The device’s output drive capability can
provide full ECL swings into 50
loads.
T ypic al Interfac e Circ uit
The circuit of Figure 1 shows a method of achieving the
least error by correcting for integral linearity, input-
induced distortion, and power-supply/ground noise. This
is achieved with the use of external reference-ladder tap
connections, an input buffer, and supply decoupling.
Contact the factory for the MAX1150/MAX1151 evalua-
tion kit manual, which contains more details on interfac-
ing the MAX1151. The function of each pin and external
connections to other components are described in the fol-
lowing sections.
VEE, AGND, DGND
V
EE
is the supply pin with AGND as ground for the
device. The power-supply pins should be bypassed as
close to the device as possible with at least a 0.01μF
ceramic capacitor. A 1μF tantalum can also be used for
low-frequency suppression. DGND is the ground for the
ECL outputs, and should be referenced to the output
pulldown voltage and appropriately bypassed, as shown
in Figure 1.
VIN (Analog Input)
There are two analog input pins that are tied to the same
point internally. Either one may be used as an analog
input sense, while the other is used for input force. This is
convenient for testing the source signal to see if there is
sufficient drive capability. The pins can also be tied to-
gether and driven by the same source. The MAX1151 is
superior to similar devices due to a preamplifier stage
before the comparators. This makes the device easier to
drive because it has constant capacitance and induces
less slew-rate distortion.
CLK, NCLK (Clock Inputs)
The clock inputs are designed to be driven differentially
with ECL levels. The duty cycle of the clock should be
kept at 50%, to avoid causing larger second harmonics.
If this is not important to the intended application, duty
cycles other than 50% may be used.
D0 to D8, DR, NDR (A and B)
The digital outputs can drive 50
to ECL levels when
pulled down to -2V. When pulled down to -5.2V, the out-
puts can drive 130
to 1k
loads. All digital outputs are
gray code, with the coding as shown in Table 1.
Table 1. Output Coding
VRBF, VRBS, VRTF, VRTS, VRM
(Reference Inputs)
There are two reference inputs and one external refer-
ence voltage tap. These are -2V (VRB force and sense),
mid-tap (VRM), and AGND (VRT force and sense). The
reference pins and tap can be driven by op amps (as
shown in Figure 1), or VRM can be bypassed for limited
temperature operation. These voltage inputs can be by-
passed to AGND for further noise suppression, if
desired.
T hermal Management
The typical thermal impedance (
θ
CA
) for the MQUAD
package has been measured at
θ
CA
= 17°C/W, in still
air with no heatsink.
To ensure rated performance, we highly recommend
using this device with a heatsink that can provide ade-
quate air flow. We have found that a Thermalloy 17846
heatsink with a minimum air flow of 1 meter/second
(200 linear feet per minute) provides adequate thermal
performance under laboratory tests. Application-specif-
ic conditions should be taken into account to ensure
that the device is properly heat sinked.
M
8-Bit, 750Msps Flash ADC
_______________________________________________________________________________________
5
V
IN
(V)
0
D8
1
D7 . . . D0
10000000
10000001
10000011
10100001
10100000
11100000
11000001
11000000
01000000
01100001
01100000
00100000
00000011
00000001
00000000
-0.5
-1.0
-1.5
-2.0
0
0
0
0
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1153BEUE | CAP 100UF 16V ELECT FC SMD |
| MAX1153 | Stand-Alone. 10-Channel. 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1154 | Stand-Alone. 10-Channel. 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1153-MAX1154 | Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1154AEUE | Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1153 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1153_10 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1153AEUE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1153AEUE+ | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。