- 您现在的位置：买卖IC网 > PDF目录383311 > MAX1154 (Maxim Integrated Products, Inc.) Stand-Alone. 10-Channel. 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor PDF资料下载
参数资料
| 型号： | MAX1154 |
| 厂商： | Maxim Integrated Products, Inc. |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | Stand-Alone. 10-Channel. 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| 中文描述： | 独立的10通道、10位系统监视器，内置温度传感器和VDD监视器 |
| 文件页数： | 21/29页 |
| 文件大小： | 481K |
| 代理商： | MAX1154 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页
M
Stand-Alone, 10-Channel, 10-Bit System Monitors
with Internal Temperature Sensor and V
DD
Monitor
______________________________________________________________________________________
21
Channel Configuration Register
Each channel has a channel configuration register (Table
13) defining the number of consecutive faults to be
detected before setting the alarm bits and generating an
interrupt, as well as controlling the digital averaging func-
tion. At power-up and after a RESET command, the regis-
ter defaults to 00 hex (no averaging, alarm on first fault).
Fault Bits
The value stored in the fault bits (B7
–
B4) in the channel
configuration register sets the number of faults that
must occur for that channel before generating an inter-
rupt. Encoding of the fault bits is straight binary with
values 0 to 15. A fault occurs in a channel when the
value in its current data register is outside the range
defined by the channel
’
s upper and lower threshold
registers. For example, if the number of faults set by the
fault bits is N, an interrupt is generated when the num-
ber of consecutive faults (see following note) reach
(N + 1). The fault bits default to 0 hex at power-up.
Note:
Consecutive faults are those happening in con-
secutive conversion scans for the same channel. If a
fault occurs and the next scan finds the input within the
normal range defined by the thresholds, the fault
counter resets. If the next counter finds the input signal
outside the opposite threshold, rather than the previous
one, the fault counter also resets. The fault counter
increments only when counting consecutive faults
exceeding the same threshold (Figure 4).
Averaging
The averaging calculated by the data-acquisition algo-
rithm of the MAX1153/MAX1154 improves the input sig-
nal-to-noise ratio (SNR) by reducing the signal
bandwidth digitally. The formula below describes the
filter implemented in the MAX1153/MAX1154:
current value = [(N - 1) / N] x past value +
[(present value) / N]
where N = number of samples indicated in Table 14.
The averaging bits (B3
–
B0) in the channel configuration
register can set the N factor to any value in Table 14.
The output of the filter-running algorithm is continuously
available in the current data register. The starting value
used by the algorithm is the initial state of the current
data register. The current data register is reset to mid-
scale (800 hex) at power-up or after a RESET com-
mand, but it can be loaded with a more appropriate
initial value to improve the filter settling time.
At power-up or after a RESET command, the B3
–
B0
bits of the channel configuration register are set to 0
hex, corresponding to a number of averaged N = 1, no
averaging. See Table 13 and the
Write-Selected
Channel Configuration Registers
section for program-
ming details. See Table 14 for N encoding.
As in all digital filters, truncation can be a cause of sig-
nificant errors. In the MAX1153/MAX1154, 24 bits of
precision are maintained in the digital averaging func-
tions, maintaining a worst-case truncation error of well
below an LSB. The worst-case truncation error in the
MAX1153/MAX1154 is given by the following:
where N = number of conversions averaged.
Therefore, the worst truncation error when averaging
256 samples is 0.01557 LSBs.
worst case truncation error
-
N
LSBs
-
=
1
16384
Table 13. Channel Configuration Register Format
B7 (MSB)
Fault B3
B6
B5
B4
B3
B2
B1
B0 (LSB)
Ave B0
Fault B2
Fault B1
Fault B0
Ave B3
Ave B2
Ave B1
Table 14. Conversion Average Encoding
CODE
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
N
1, no averaging
2
4
8
16
32
64
128
256
512
1024
2048
Reserved
Reserved
Reserved
Reserved
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1153-MAX1154 | Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1154AEUE | Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1154BEUE | Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX1153AEUE | Stand-Alone, 10-Channel, 10-Bit System Monitors with Internal Temperature Sensor and VDD Monitor |
| MAX115 | 2x4-Channel, Simultaneous-Sampling 12-Bit ADCs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1154AEUE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1154AEUE+ | 功能描述:模数转换器 - ADC HQ PN TESTED 16-TSSOP 173 MIL RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1154AEUE+T | 功能描述:模数转换器 - ADC NULL RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1154AEUE-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1154BEUE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。