- 您现在的位置：买卖IC网 > PDF目录9975 > MAX11607EWC+T (Maxim Integrated Products)IC ADC SERIAL 10BIT 4CH 12WLP PDF资料下载
参数资料
| 型号： | MAX11607EWC+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC ADC SERIAL 10BIT 4CH 12WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 采样率（每秒）： | 94.4k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.29W |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFBGA，WLCSP |
| 供应商设备封装： | 12-WLP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，单极；2 个差分，双极 |
MAX11606–MAX11611
Low-Power, 4-/8-/12-Channel, I2C,
10-Bit ADCs in Ultra-Small Packages
18
Maxim Integrated
using an external reference or VDD as a reference, all
analog circuitry is inactive in shutdown and supply cur-
rent is less than 0.5A (typ). The digital conversion
results obtained in internal clock mode are maintained
in memory during shutdown and are available for
access through the serial interface at any time prior to a
STOP or a repeated START condition.
When idle, the MAX11606–MAX11611 continuously wait
for a START condition followed by their slave address (see
Slave Address section). Upon reading a valid address
byte the MAX11606–MAX11611 power-up. The internal
reference requires 10ms to wake up, so when using the
internal reference it should be powered up 10ms prior to
conversion or powered continuously. Wake-up is invisible
when using an external reference or VDD as the reference.
Automatic shutdown results in dramatic power savings,
particularly at slow conversion rates and with internal
clock. For example, at a conversion rate of 10ksps, the
average supply current for the MAX11607 is 60A (typ)
and drops to 6A (typ) at 1ksps. At 0.1ksps the average
supply current is just 1A, or a minuscule 3W of power
consumption, see Average Supply Current vs. Conversion
Rate in the
Typical Operating Characteristics).
Reference Voltage
SEL[2:0] of the setup byte (Table 1) control the reference
and the AIN_/REF configuration (Table 6). When
AIN_/REF is configured to be a reference input or refer-
ence output (SEL1 = 1), differential conversions on
AIN_/REF appear as if AIN_/REF is connected to GND
(see note 2 of Table 4). Single-ended conversion in scan
mode on AIN_/REF is ignored by internal limiter, which
sets the highest available channel at AIN2 or AIN10.
Internal Reference
The internal reference is 4.096V for the MAX11606/
MAX11608/MAX11610 and 2.048V for the MAX11607/
MAX11609/MAX11611. SEL1 of the setup byte controls
whether AIN_/REF is used for an analog input or a refer-
ence (Table 6). When AIN_/REF is configured to be an
internal reference output (SEL[2:1] = 11), decouple
AIN_/REF to GND with a 0.1F capacitor and a 2k
Ω series
resistor (see the
Typical Operating Circuit). Once powered
up, the reference always remains on until reconfigured.
The internal reference requires 10ms to wake up and is
accessed using SEL0 (Table 6). When in shutdown, the
internal reference output is in a high-impedance state. The
reference should not be used to supply current for exter-
nal circuitry. The internal reference does not require an
SEL2
SEL1
SEL0
REFERENCE
VOLTAGE
AIN_/REF
(MAX11606/
MAX11607/
MAX11610/
MAX11611)
REF
(MAX11608/
MAX11609)
INTERNAL
REFERENCE STATE
00
X
VDD
Analog input
Not connected
Always off
0
1
X
External reference
Reference input
Always off
1
0
Internal reference
Analog input
Not connected
Always off
1
0
1
Internal reference
Analog input
Not connected
Always on
1
0
Internal reference
Reference output
Always off
1
Internal reference
Reference output
Always on
Table 6. Reference Voltage, AIN_/REF, and REF Format
OUTPUT CODE
FULL-SCALE
TRANSITION
11 . . . 111
11 . . . 110
11 . . . 101
00 . . . 011
00 . . . 010
00 . . . 001
00 . . . 000
12
3
0
FS
FS - 3/2 LSB
FS = VREF
ZS = GND
INPUT VOLTAGE (LSB)
MAX11606–
MAX11611
1 LSB =
VREF
1024
Figure 12. Unipolar Transfer Function
X = Don’t care.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72271LA15TFI8 | IC FIFO 16384X18 LP 15NS 64QFP |
| IDT82V2044EPF8 | IC LIU T1/E1 QUAD SHORT 128-TQFP |
| MS27473P14F18P | CONN PLUG 18POS STRAIGHT W/PINS |
| IDT82V2044EPFG8 | IC LINE INTERFC UNIT 4CH 128TQFP |
| IDT72271LA10TF8 | IC FIFO 16384X18 LP 10NS 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11608 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel, 2-Wire Serial 10-Bit ADCs |
| MAX11608EEE+ | 功能描述:模数转换器 - ADC 10-Bit 8Ch 94.4sps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11608EEE+T | 功能描述:模数转换器 - ADC 10-Bit 8Ch 94.4sps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11609 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel, 2-Wire Serial 10-Bit ADCs |
| MAX11609EEE+ | 功能描述:模数转换器 - ADC 10-Bit 8Ch 94.4sps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。