- 您现在的位置：买卖IC网 > PDF目录9707 > MAX11800ETC/V+ (Maxim Integrated Products)IC TOUCH SCREEN CTRLR LP 12WQFN PDF资料下载
参数资料
| 型号： | MAX11800ETC/V+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/59页 |
| 文件大小： | 0K |
| 描述： | IC TOUCH SCREEN CTRLR LP 12WQFN |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | 可供 |
| 数据接口： | 串行，SPI? |
| 数据速率/采样率 (SPS，BPS)： | 105k |
| 电源电压： | 1.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WQFN 裸露焊盘 |
| 供应商设备封装： | 12-TQFN-EP（4x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
MAX11800–MAX11803
Low-Power, Ultra-Small Resistive Touch-Screen
Controllers with I2C/SPI Interface
______________________________________________________________________________________
35
For example:
0000 = 2-1 LSB = aperture checking disabled
0001 = 2(1-1) LSB = ±1 LSB
0010 = 2(2-1) LSB = ±2 LSB
0011 = 2(3-1) LSB = ±4 LSB
…
1001 = 2(9-1) LSB = ±256 LSB (1/16 of the touch screen
in each direction)
1010 = 2(10-1) LSB = ±512 LSB (1/8 of the touch screen
in each direction)
1011 = 2(11-1) LSB = ±1024 LSB (1/4 of the touch
screen in each direction)
1100 = 2(12-1) LSB = ±2048 LSB (1/2 of the touch
screen in each direction)
1101 to 1111 = aperture checking disabled
FIFO Aperture Criteria
In autonomous mode with aperture engaged, new data
is written to the FIFO, and an interrupt is issued when
the following conditions occur (aperture mode is not
available in direct conversion mode).
New Panel Touch Initiated
The FIFO updates and issues an interrupt when a new
touch is observed on the panel (data tag = 00). This
event occurs regardless of the current aperture setting
and the previous touch location so that multiple presses
in the same location can be observed and registered.
Continuous Panel Touch Terminated
The FIFO updates and issues an interrupt when a con-
tinuous panel touch is terminated (data tag = 10). This
event occurs regardless of the current aperture setting
and the previous continuous touch location(s) so that
multiple presses in the same location can be observed
and registered.
Continuous Panel Touch
Measurement Meets Aperture Criteria
The MAX11800/MAX11801 log the measurement data
to the FIFO and issue an interrupt when a measurement
during a continuous panel touch (event tag = 01) meets
the aperture criteria (i.e., lies on or outside the aperture
boundary). This event occurs when the point of contact
is dragged across the touch screen. Only the
ΔX or ΔY
aperture criteria need to be met and a greater than or
equal to qualification criterion is applied. If the change
in X position or change in Y position exceeds the aper-
ture criteria, then an interrupt is generated.
Applications Information
Using Aperture Mode
Aperture mode is only supported in the MAX11800/
MAX11801. The MAX11800/MAX11801 accommodate
touch-panel applications where limited resolution in
both time and space can be traded off for reduced
microprocessor activity. A simulated keypad is an
example of an application where autonomous conver-
sion mode with aperture checking could yield an effi-
cient solution.
The AP determines the durations of touch-screen
presses. An issuance of TIRQ interrupts accompanies
all FIFO events. The interrupts clear when all existing
data is read back by the AP, allowing the AP to correct-
ly interpret held panel data.
The FIFO updates immediately when a new touch event
is detected. The system assumes that the panel touch is
continuous after the AP receives the interrupt. The
MAX11800/MAX11801 continue to scan the panel at the
user-programmed sample rate. The FIFO updates when
the measurement data shows that the panel touch loca-
tion moves (i.e., a measurement exceeds either of the
selected aperture ranges). The FIFO also updates upon
detection of a panel release. The AP determines the
duration of the press by observing the time between the
leading edge of the touch (tag 00) and the release edge
of the touch (tag 10). All midpress data (tag 01) are inter-
preted as part of a dragged touch event.
All valid touch events log two data points into the FIFO:
an initial data point at the beginning of the touch (tag
00) and a release data point at the termination of the
touch (tag 10). Discard release edge position data as
invalid as the MAX11800/MAX11801 cannot determine
at which point in the ADC conversion cycle the panel is
released during the measurement operation. If the
release occurs while the ADC is actively sampling the
panel, the results are invalid. Only initial and midpress
position data are reliable.
Any touch event too short in duration to log both initial
and release data points is recorded in the FIFO as a
release (tag 10) and discarded as a glitch event.
Measuring durations of panel touches becomes
impractical when the AP services the MAX11800/
MAX11801 at lower than the operating speed of the
devices and the panel combined. The AP cannot time
the duration between panel touches when both the ini-
tial and release data points can be logged before the
initial interrupt is serviced. Do not allow the FIFO to
overflow as touch information can be lost and the FIFO
content becomes invalid.
相关PDF资料 |
PDF描述 |
|---|---|
| MC100EP16VTDTR2 | IC RCVR/DRVR ECL DIFF VAR 8TSSOP |
| V24B24M150BL | CONVERTER MOD DC/DC 24V 150W |
| MAX11801ETC/V+ | IC TOUCH SCREEN CTRLR LP 12WQFN |
| V24B24M150B | CONVERTER MOD DC/DC 24V 150W |
| M83723/86R1002N | CONN PLUG 2POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11800EVKIT+ | 功能描述:显示开发工具 MAX11800 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX11800EWC+T | 功能描述:触摸屏转换器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX11800GTC/V+ | 功能描述:触摸屏转换器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX11800GTC/V+T | 功能描述:触摸屏转换器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX11800TEVS+ | 功能描述:显示开发工具 SPI 4Ch Touch Screen Controller RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
发布紧急采购，3分钟左右您将得到回复。