参数资料
| 型号： | MAX118EAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT 1MSPS 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 位数： | 8 |
| 采样率（每秒）： | 1M |
| 数据接口： | 并联 |
| 转换器数目： | 3 |
| 功率耗散（最大）： | 762mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 8 个单端，单极 |
MAX114/MAX118
+5V, 1Msps, 4 & 8-Channel,
8-Bit ADCs with 1A Power-Down
_______________________________________________________________________________________
7
_______________Detailed Description
Converter Operation
The MAX114/MAX118 use a half-flash conversion tech-
nique (see
Functional Diagram) in which two 4-bit flash
ADC sections achieve an 8-bit result. Using 15 com-
parators, the flash ADC compares the unknown input
voltage to the reference ladder and provides the upper
four data bits. An internal digital-to-analog converter
(DAC) uses the four most significant bits (MSBs) to
generate both the analog result from the first flash con-
version and a residue voltage that is the difference
between the unknown input and the DAC voltage. The
residue is then compared again with the flash com-
parators to obtain the lower four data bits (LSBs).
An internal analog multiplexer enables the devices to
read four (MAX114) or eight (MAX118) different analog
voltages under microprocessor (P) control. One of the
MAX118’s analog channels, IN8, is internally hard-
wired and always reads VREF+ when selected.
Power-Down Mode
In burst-mode or low sample-rate applications, the
MAX114/MAX118 can be shut down between conver-
sions, reducing supply current to microamp levels (see
Typical Operating Characteristics). A logic low on the
PWRDN pin shuts the devices down, reducing supply
current typically to 1A when powered from a single +5V
supply. A logic high on
PWRDN wakes up the
MAX114/MAX118, and the selected analog input enters
the track mode. The signal is fully acquired after 360ns
(this includes both the power-up delay and the track/hold
acquisition time), and a new conversion can be started.
If the power-down feature is not required, connect
PWRDN to VDD. For minimum current consumption, keep
digital inputs at the supply rails in power-down mode.
Refer to the
Reference section for information on reduc-
ing reference current during power-down.
___________________Digital Interface
The MAX114/MAX118 have two basic interface modes,
which are set by the MODE pin. When MODE is low,
the converters are in read mode; when MODE is high,
the converters are set up for write-read mode. The A0,
A1, and A2 inputs control channel selection, as shown
in Table 1. The address must be valid for a minimum
time, tACQ, before the next conversion starts.
Read Mode (MODE = 0)
In read mode, conversions and data access are con-
trolled by the
RD input (Figure 3). The comparator
inputs track the analog input voltage for the duration of
tACQ. Initiate a conversion by driving CS and RD low.
With Ps that can be forced into a wait state, hold
RD
low until output data appears. The P starts the conver-
sion, waits, and then reads data with a single read
instruction.
DATA
OUTPUTS
DATA
OUTPUTS
CL
RL = 3k
CL
a) HIGH-Z TO VOH
b) HIGH-Z TO VOL
RL = 3k
VDD
Figure 1. Load Circuits for Data-Access Time Test
DATA
OUTPUTS
10pF
3k
10pF
a) VOH TO HIGH-Z
b) VOL TO HIGH-Z
3k
VDD
DATA
OUTPUTS
Figure 2. Load Circuits for Data-Hold Time Test
IN2
IN1
01
SELECTED CHANNEL
IN4
IN3
11
10
IN6
IN5
——
IN8
(reads VREF+ if selected)
IN7
——
MAX114
00
Table 1. Truth Table for Input Channel
Selection
00
1
01
1
01
0
10
1
11
1
11
0
10
0
MAX118
00
0
A2
A1
A0
A1
A0
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1191ETI+T | IC ADC 8BIT 7.5MSPS DL 28-TQFN |
| MAX1192ETI+T | IC ADC 8BIT 22MSPS DL 28-TQFN |
| MAX1195ECM+TD | IC ADC 8BIT 40MSPS DL 48-TQFP |
| MAX1197ECM+TD | IC ADC 8BIT 60MSPS DL 48-TQFP |
| MAX1202AEPP+ | IC ADC 12BIT 8CH 20-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX118EAI+ | 功能描述:模数转换器 - ADC 8-Bit 8Ch 1Msps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX118EAI+T | 功能描述:模数转换器 - ADC 8-Bit 8Ch 1Msps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX118EAI-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX118EPI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX118EPI+ | 功能描述:模数转换器 - ADC 8-Bit 8Ch 1Msps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。