- 您现在的位置：买卖IC网 > Datasheet目录471 > MAX12000ETB+T (Maxim Integrated)IC AMP GPS FRONT 1575MHZ 10TDFN Datasheet资料下载
参数资料
| 型号： | MAX12000ETB+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | IC AMP GPS FRONT 1575MHZ 10TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 1.575GHz |
| 增益： | 15dB ~ 18.5dB |
| 噪音数据： | 1dB ~ 1.3dB |
| RF 型： | GPS |
| 电源电压： | 3 V ~ 5 V |
| 电流 - 电源： | 15mA ~ 30.2mA |
| 测试频率： | 1.575GHz |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
1575MHz GPS Front-End Amplifier
Detailed Description
The MAX12000 IC contains two LNA stages tuned for
use at 1575MHz.
AMP 1
AMP 1 has an internal load that limits the bandwidth
and provides a 50 ? output impedance through a DC-
blocking capacitor. The internal biasing for AMP 1 sup-
presses gain variation with changes in temperature and
supply voltage. At the input, an integrated DC-blocking
capacitor and matching network are intentionally omit-
ted to allow selection of external components to opti-
mize for noise or gain.
AMP 2 with Gain Step
The output of AMP 2 has the dual role of providing both
the RF output drive and receiving the DC power supply
through a single cable. Both the input and output ports
of AMP 2 are internally matched to 50 ? impedance at
1575MHz. A 3.4dB gain switch can be used to adjust
the gain for different applications. The gain-select pin is
connected to an inverter with an internal pullup resistor.
Hence, the gain-select pin is set by default to high-gain
mode. Shorting the gain-select pin to ground sets the
Supply
The IC power can be supplied from the navigation sys-
tem through the RF cable (pin 5). An integrated filter
circuit is connected to the output of LNA 2 to separate
the supply voltage from the GPS signal. Alternatively,
the supply voltage can be applied to the external
capacitor pin (pin 4).
Layout Considerations
For best performance, carefully lay out the printed cir-
cuit board using high-frequency techniques. Use con-
trolled-impedance transmission lines to interface with
the MAX12000 high-speed inputs and outputs and iso-
late the input signals from the output signals as much
as possible. For improved noise figure, keep the con-
nection to the input of LNA 1 as short as possible. A
power-supply decoupling capacitor should be placed
very close to pin 4 and connected directly to a ground
plane. If low-gain selection for LNA 2 is required, con-
nect pin 7 directly to the ground plane with a very short
printed circuit board trace. Good grounding is critical
for this device. The backside ground plane should be
as close as possible. See Figure 1 for printed circuit
board layout.
gain stage to a 3.4dB lower gain. As with AMP 1, AMP
2 has an internal load that limits the bandwidth, and the
amplifier’s internal biasing suppresses gain variation
with changes in temperature and supply voltage.
Typical Operating Circuit
SAW
PINNING:
1 = LNA 2 INPUT
2 = GND
3 = GND
4 = EXTCAP/ALT_V CC
10
1
4
5 = LNA 2 OUTPUT/V CC
6 = LNA 1 INPUT
7 = GAIN SETTING
8 = GND
9 = GND
10 = LNA 1 OUTPUT
V CC
REG
V CC
REG
MATCHING
NETWORK/
DC BLOCK
6
LNA 1
MAX12000
LNA 2
5
7
OUTPUT
GAIN SETTING
OPEN = 31.4dB GAIN
8/9
EXPOSED PADDLE
2/3
SHORT TO GROUND = 28dB GAIN
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX12005ETM+T | IC SATELLITE IF SWITCH 48-TQFN |
| MAX1385BUTM+ | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
| MAX1470EVKIT-315 | EVAL KIT FOR MAX1470 315MHZ |
| MAX1471EVKIT-315 | EVAL KIT FOR MAX1471 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX12001ETB | 制造商:Maxim Integrated Products 功能描述: |
| MAX12001ETB+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX12001ETB+T | 功能描述:射频放大器 1575MHz GPS LNA RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX12005ETM+ | 功能描述:RF 开关 IC Satellite IF Switch RoHS:否 制造商:M/A-COM Technology Solutions 开关数量:Single 开关配置:SPDT 介入损耗:0.6 dB 截止隔离（典型值）:43 dB 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PQFN-16 封装:Reel |
| MAX12005ETM+CF7 | 制造商:Maxim Integrated Products 功能描述:SATELLITE IF SWITCH - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。