参数资料
| 型号： | MAX1233ETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/44页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR TOUCH 28-TQFN |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1，4 x 4 小键盘 |
| 分辨率（位）： | 8，10，12 b |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 数据速率/采样率 (SPS，BPS)： | 50k |
| 电压基准： | 外部，内部 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
MAX1233/MAX1234
±15kV ESD-Protected Touch-Screen
Controllers Include DAC and Keypad Controller
16
______________________________________________________________________________________
Output Buffer
The DAC voltage output is an internally buffered unity-
gain follower that slews at up to ±0.4V/s. The output
can swing from zero to full scale. With a 1/4FS to 3/4FS
output transition, the amplifier output typically settles to
1/2LSB in less than 5s when loaded with 10kΩ in par-
allel with 50pF. The buffer amplifier is stable with any
combination of resistive loads >10k
Ω and capacitive
loads <50pF.
Power-On Reset
All registers of the MAX1233/MAX1234 power up at a
default zero state, except the DAC data register, which
is set to 10000000, so the output is at midscale.
Keypad Controller and GPIO
The keypad controller is designed to interface a matrix-
type 4 rows
× 4 columns (16 keys or fewer) keypad to a
host controller. The KEY control register controls keypad
interrupt, keypad scan, and keypad debounce times.
The KeyMask and ColumnMask registers enable mask-
ing of a particular key or an entire column of the keypad
when they are not in use. The MAX1233/MAX1234 offer
two keypad data registers. KPData1 is the pending reg-
ister. KPData2 holds keypad scan results of only the
unmasked keys. If 12 or fewer keys are being monitored,
one or more of the row/column pins of the
MAX1233/MAX1234 can be software programmed as
GPIO pins.
Touch-Screen Detection
Touch-screen detection can be enabled or disabled by
writing to the ADC control register as shown in Table 4.
Touch-screen detection is disabled at initial power-up.
Once touch-screen detection is enabled, the Y- driver
is on and the Y- pin is connected to GND. The X+ pin is
internally pulled to AVDD through a 1MΩ resistor as
shown in Figure 6. When the screen is touched, the X+
pin is pulled to GND through the touch screen and a
touch is detected.
When the 1MΩ pullup resistor is first connected, the X+
pin can be floating near ground. To prevent false touch
detection in this case, the X+ pin is precharged high for
0.1s using the 7Ω PMOS driver before touch detection
begins.
Key-Press Detection
Key-press detection can be enabled or disabled by
writing to the keypad control register as shown in Table
17. Key-press detection is disabled at initial power-up.
Once key-press detection is enabled, the C_ pins are
internally connected to DVDD and the R_ pins are inter-
nally pulled to GND through a 16kΩ resistor. When a
key is pressed, the associated row pin is pulled to
DVDD and the key press is detected. Figure 7 shows
the key-press detection circuitry.
Interrupts
PEN Interrupt Request (
PENIRQ)
The
PENIRQ output can be used to alert the host con-
troller of a screen touch. The
PENIRQ output is normally
high and goes low after a screen touch is detected.
SW1
SW2
SW255
OUT
VREF
Figure 5. DAC Current-Steering Topology
S2
S1
1M
Ω
+AVDD
X+
Y+
X-
Y-
TOUCH-SCREEN
DETECTOR
PENIRQ
TOUCH
SCREEN
Figure 6. Touch-Screen Detection Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1242AEPA+ | IC ADC 10BIT SERIAL 8-DIP |
| MAX1245AEPP+ | IC ADC 12BIT SERIAL 20-DIP |
| MAX1246AEPE+ | IC ADC 12BIT SERIAL 16-DIP |
| MAX1249BCEE | IC ADC 4CH 10BIT 133KSPS 16-QSOP |
| MAX1253BEUE+T | IC ADC 12BIT W/REF 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1233ETI+ | 功能描述:触摸屏转换器和控制器 4Ch uWire QSPI/SPI Touch Interface RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX1233ETI+T | 功能描述:触摸屏转换器和控制器 4Ch uWire QSPI/SPI Touch Interface RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX1234EGI | 功能描述:触摸屏转换器和控制器 RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX1234EGI+ | 制造商:Maxim Integrated Products 功能描述:TOUCH SCREEN CONTROLLER 28-PIN QFN EP - Rail/Tube |
| MAX1234EGI-T | 功能描述:触摸屏转换器和控制器 RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
发布紧急采购，3分钟左右您将得到回复。