参数资料
| 型号： | MAX1234ETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/44页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR TOUCH 28-TQFN |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1，4 x 4 小键盘 |
| 分辨率（位）： | 8，10，12 b |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 数据速率/采样率 (SPS，BPS)： | 50k |
| 电压基准： | 内部 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
MAX1233/MAX1234
±15kV ESD-Protected Touch-Screen
Controllers Include DAC and Keypad Controller
30
______________________________________________________________________________________
ence power-up status when the A/D0–A/D3 bits are
zero. These values can be set initially on power-up.
(Subsequently A/D0–A/D3 bits are not zero, and any
other value of these bits is exclusive to ADC resolution
programming.)
Differential Ratiometric Touch-Position
Measurement
The MAX1233/MAX1234 provide differential conver-
sions. Figure 12 shows the switching matrix configura-
tion for Y coordinate measurement. The +REF and -REF
inputs are connected directly to Y+ and Y-. The conver-
sion result is a percentage of the external resistances,
and is unaffected by variation in the total touch-screen
resistance or the on-resistance of the internal switching
matrix. The touch screen remains powered during the
acquisition and conversion process.
Touch-Screen Settling
There are two mechanisms that affect the voltage level
at the point where the touch panel is pressed. One is
electrical ringing due to parasitic capacitance between
the top and bottom layers of the touch screen and the
other is the mechanical bouncing caused by vibration
of the top layer of the touch screen. Thus, the input sig-
nal, reference, or both may not settle into their final
steady-state values before the ADC samples the inputs,
and the reference voltage may continue to change dur-
ing the conversion cycle. The MAX1233/MAX1234 can
be programmed to wait for a fixed amount of time after
a screen touch has been detected before beginning a
scan. Use the touch-screen settling control bits in the
ADC control register (Table 11) to set the settling delay
to between zero and 100ms.
The settling problem is amplified in some applications
where external filter capacitors may be required across
the touch screen to filter noise that may be generated
by the LCD panel or backlight circuitry, etc. The values
of these capacitors cause an additional settling time
requirement when the panel is touched. Any failure to
settle before conversion start may show up as a gain
error. Average the conversion result by writing to the
ADC control register, as shown in Table 10, to minimize
noise.
Touch-Pressure Measurement
The MAX1233/MAX1234 provide two methods of mea-
surement of the pressure applied to the touch screen.
Although 8-bit resolution is typically sufficient, the follow-
ing calculations use 12-bit resolution demonstrating the
maximum precision of the MAX1233/MAX1234. Figure 13
shows the pressure measurement block diagram.
The first method performs pressure measurements
using a known X-plate resistance. After completing
three conversions, X-position, Z1-position, and Z2 posi-
tion, use the following equation to calculate RTOUCH :
The second method requires knowing both the X-plate
and Y-plate resistance. Three touch-screen conver-
sions are required in this method as well for measure-
ment of the X-position, Y-position, and Z- position of the
touch screen. Use the following equation to calculate
RTOUCH:
R
Z
X
Z
R
Y
TOUCH
XPLATE
POSITION
YPLATE
POSITION
=
×
×
×
11
4096
1
4096
RR
XZ
Z
TOUCH
XPLATE
POSITION
=
()×
×
4096
1
2
1
GND
FORCE LINE
SENSE LINE
FORCE LINE
+AVDD
Y-
X+
Y+
+IN
+REF
-REF
-IN
CONVERTER
Figure 12. Ratiometric Y-Coordinate Measurement
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B4H-MW-F1 | CONVERTER MOD DC/DC 52V 100W |
| VI-B4F-MW-F4 | CONVERTER MOD DC/DC 72V 100W |
| V24B3V3M100B | CONVERTER MOD DC/DC 3.3V 100W |
| MAX11800ETC/V+ | IC TOUCH SCREEN CTRLR LP 12WQFN |
| MC100EP16VTDTR2 | IC RCVR/DRVR ECL DIFF VAR 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1234ETI+ | 功能描述:触摸屏转换器和控制器 4Ch uWire QSPI/SPI Touch Interface RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX1234ETI+T | 功能描述:触摸屏转换器和控制器 4Ch uWire QSPI/SPI Touch Interface RoHS:否 制造商:Microchip Technology 类型:Resistive Touch Controllers 输入类型:3 Key 数据速率:140 SPS 分辨率:10 bit 接口类型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 电源电压:2.5 V to 5.25 V 电源电流:17 mA 工作温度:- 40 C to + 85 C 封装 / 箱体:SSOP-20 |
| MAX1234EVC16 | 功能描述:数据转换 IC 开发工具 MAX1233/34 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1234EVKIT | 制造商:Maxim Integrated Products 功能描述:+15KV ESD-PROTECTED TOUCH-SCREEN CO - Rail/Tube |
| MAX1236EUA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。