- 您现在的位置：买卖IC网 > PDF目录9507 > MAX127BCAI+ (Maxim Integrated Products)IC DAS 12BIT 2-WIRE 28-SSOP PDF资料下载
参数资料
| 型号： | MAX127BCAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC DAS 12BIT 2-WIRE 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 类型： | 数据采集系统（DAS），ADC |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 8k |
| 数据接口： | I²C，串行 |
| 电压电源： | 单电源 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1393 (CN2011-ZH PDF) |
The MAX127/MAX128 ignore acknowledge and NOT-
acknowledge conditions issued by the master during
the read cycle. The device waits for the master to read
the output data or waits until a STOP condition is
issued. Figure 10 shows a complete read cycle.
In unipolar input mode, the output is straight binary. For
bipolar input mode, the output is two’s complement. For
output binary codes see the
Transfer Function section.
Applications Information
Power-On Reset
The MAX127/MAX128 power up in normal operating
mode, waiting for a START condition followed by the
appropriate slave address. The contents of the input
and output data registers are cleared at power-up.
Internal or External Reference
The MAX127/MAX128 operate with either an internal or
an external reference (Figures 11a–11c). An external
reference is connected to either REF or to REFADJ.
The REFADJ internal buffer gain is trimmed to 1.6384 to
provide 4.096V at REF from a 2.5V reference.
Internal Reference
The internally trimmed 2.50V reference is amplified
through the REFADJ buffer to provide 4.096V at REF.
Bypass REF with a 4.7F capacitor to AGND and bypass
REFADJ with a 0.01F capacitor to AGND (Figure 11a).
The internal reference voltage is adjustable to ±1.5%
(±65 LSBs) with the reference-adjust circuit of Figure 12.
External Reference
To use the REF input directly, disable the internal buffer
by connecting REFADJ to VDD (Figure 11b). Using the
REFADJ input eliminates the need to buffer the refer-
ence externally. When the reference is applied at
REFADJ, bypass REFADJ with a 0.01F capacitor to
AGND (Figure 11c).
At REF and REFADJ, the input impedance is a mini-
mum of 10k
for DC currents. During conversions, an
external reference at REF must be able to drive a
400A DC load, and must have an output impedance
of 10
or less. If the reference has higher input imped-
ance or is noisy, bypass REF with a 4.7F capacitor to
AGND as close to the chip as possible.
With an external reference voltage of less than 4.096V
at REF or less than 2.5V at REFADJ, the increase in
RMS noise to the LSB value (full-scale voltage/4096)
results in performance degradation and loss of effec-
tive bits.
Power-Down Mode
To save power, put the converter into low-current shut-
down mode between conversions. Two programmable
power-down modes are available, in addition to the
hardware shutdown. Select STBYPD or FULLPD by pro-
gramming PD0 and PD1 in the input control byte (Table
4). When software power-down is asserted, it becomes
effective only after the end of conversion. In all power-
down modes, the interface remains active and conver-
sion results may be read. Input overvoltage protection
is active in all power-down modes.
MAX127/MAX128
Multirange, +5V, 12-Bit DAS with
2-Wire Serial Interface
______________________________________________________________________________________
13
Figure 10. Complete 2-Wire Serial Read Transmission
START
CONDITION
STOP
CONDITION
LSB DATA BYTE
MSB DATA BYTE
SLAVE ADDRESS BYTE
MSB
LSB
0
1
2
7
8
9
10
11
17
18
19
22
23
26
27
R
A
D11
D4
A
D3
D0
A
FILLED WITH
4 ZEROS
相关PDF资料 |
PDF描述 |
|---|---|
| VE-24M-MY-S | CONVERTER MOD DC/DC 10V 50W |
| MAX1270BCAI+ | IC ADC 12-BIT MULTIRANGE 28-SSOP |
| VE-24L-MY-S | CONVERTER MOD DC/DC 28V 50W |
| VE-24K-MY-S | CONVERTER MOD DC/DC 40V 50W |
| MAX186CCWP+ | IC ADC 12BIT SERIAL 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX127BCAI+ | 功能描述:数据转换系统 12-Bit 8Ch 8ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 转换速率:0.001 MSPs 分辨率:24 bit 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX127BCAI+ | 制造商:Maxim Integrated Products 功能描述:CONVERTOR AD ((NW)) |
| MAX127BCAI+T | 功能描述:数据转换系统 12-Bit 8Ch 8ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 转换速率:0.001 MSPs 分辨率:24 bit 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX127BCAI-T | 功能描述:数据转换系统 RoHS:否 制造商:Texas Instruments 转换速率:0.001 MSPs 分辨率:24 bit 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX127BCNG | 功能描述:数据转换系统 RoHS:否 制造商:Texas Instruments 转换速率:0.001 MSPs 分辨率:24 bit 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。