- 您现在的位置：买卖IC网 > PDF目录10492 > MAX1297BEEG+ (Maxim Integrated Products)IC ADC 12BIT 265KSPS 24-QSOP PDF资料下载
参数资料
| 型号： | MAX1297BEEG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/19页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 265KSPS 24-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 位数： | 12 |
| 采样率（每秒）： | 265k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 667mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；2 个单端，双极；1 个伪差分，单极；1 个伪差分，双极 |
| 产品目录页面： | 1396 (CN2011-ZH PDF) |
MAX1295/MAX1297
265ksps, +3V, 6-/2-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
14
______________________________________________________________________________________
the chip-select signal, which enables a P to address
the MAX1295/MAX1297 as an I/O port. When high, CS
disables the CLK, WR, and RD inputs and forces the
interface into a high-impedance (high-Z) state.
Input Format
The control bit sequence is latched into the device on
pins D7–D0 during a write command. Table 4 shows
the control-byte format.
Output Data Format
The 12-bit-wide output format for both the MAX1295/
MAX1297 is binary in unipolar mode and two’s comple-
ment in bipolar mode. CS, RD, WR, INT, and the 12 bits
of output data can interface directly to a 16-bit data bus.
When reading the output data, CS and RD must be low.
__________Applications Information
Power-On Reset
When power is first applied, internal power-on reset cir-
cuitry activates the MAX1295/MAX1297 in external clock
mode and sets INT high. After the power supplies stabi-
lize, the internal reset time is 10s; no conversions
should be attempted during this phase. When using the
internal reference, 500s is required for VREF to stabilize.
Internal and External Reference
The MAX1295/MAX1297 can be used with an internal
or external reference voltage. An external reference
can be connected directly to REF or REFADJ.
An internal buffer is designed to provide +2.5V at REF for
both the MAX1295 and MAX1297. The internally trimmed
+1.22V reference is buffered with a +2.05V/V gain.
Internal Reference
The full-scale range with the internal reference is +2.5V
with unipolar inputs and ±1.25V with bipolar inputs. The
internal reference buffer allows for small adjustments
(±100mV) in the reference voltage (Figure 7).
Note: The reference buffer must be compensated with
an external capacitor (4.7F min) connected between
REF and GND to reduce reference noise and switching
spikes from the ADC. To further minimize noise on the
reference, connect a 0.01F capacitor between REFADJ
and GND.
External Reference
With both the MAX1295 and MAX1297, an external refer-
ence can be placed at either the input (REFADJ) or the
output (REF) of the internal reference buffer amplifier.
Using the REFADJ input makes buffering the external
reference unnecessary. The REFADJ input impedance
is typically 17k
.
When applying an external reference to REF, disable
the internal reference buffer by connecting REFADJ to
VDD. The DC input resistance at REF is 25k
.
Therefore, an external reference at REF must deliver up
to 200A DC load current during a conversion and
have an output impedance less than 10
. If the refer-
ence has higher output impedance or is noisy, bypass
it close to the REF pin with a 4.7F capacitor.
Power-Down Modes
To save power, place the converter in a low-current
shutdown state between conversions. Select standby
mode or shutdown mode using bits D6 and D7 of the
control byte (Tables 1 and 4). In both software power-
down modes, the parallel interface remains active, but
the ADC does not convert.
Standby Mode
While in standby mode, the supply current is typically
850A. The part powers up on the next rising edge of
WR and is ready to perform conversions. This quick
turn-on time allows the user to realize significantly
reduced power consumption for conversion rates
below 265ksps.
D6
D4
D5
PD0
SGL/DIF
ACQMOD
A2
A0
A1
D2
D0
(LSB)
UNI/BIP
PD1
D1
D3
D7
(MSB)
Table 4. Control-Byte Format
VDD = +3V
330k
50k
GND
50k
0.01
F
4.7
F
REFADJ
REF
MAX1295
MAX1297
Figure 7. Reference Adjustment with External Potentiometer
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1268BEEG+ | IC ADC 12BIT 420KSPS 24-QSOP |
| MAX1181ECM+D | IC ADC 10BIT 80MSPS DUAL 48-TQFP |
| MAX11040KGUU+ | IC ADC 24BIT 4CH 38-TSSOP |
| UP050SL100J-A-B | CAP CER 10PF 50V 5% AXIAL |
| ICL7109CMH+D | IC ADC 12BIT 3-ST 44-MQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1297BEEG+ | 功能描述:模数转换器 - ADC 12-Bit 2Ch 265ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1297BEEG+T | 功能描述:模数转换器 - ADC 12-Bit 2Ch 265ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1297BEEG-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1298AEAE | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1298AEAE+ | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。