- 您现在的位置：买卖IC网 > PDF目录2008 > MAX1303BEUP+ (Maxim Integrated Products)IC ADC 16BIT MULT RANGE 20TSSOP PDF资料下载
参数资料
| 型号： | MAX1303BEUP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/29页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT MULT RANGE 20TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS |
| 标准包装： | 74 |
| 位数： | 16 |
| 采样率（每秒）： | 115k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 879mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
MAX1303
4-Channel, ±VREF Multirange Inputs,
Serial 16-Bit ADC
______________________________________________________________________________________
27
Gain Error
When a positive full-scale voltage is applied to the con-
verter inputs, the digital output is all ones (0xFFFF). The
transition from 0xFFFE to 0xFFFF occurs at 1.5 LSB
below full scale. Gain error is the amount of deviation
between the measured full-scale transition point and
the ideal full-scale transition point with the offset error
removed and all untested channels grounded.
Unipolar Endpoint Overlap
Unipolar endpoint overlap is the change in offset when
switching between complementary input voltage
ranges. For example, the difference between the volt-
age that results in a 0xFFFF output in the -VREF/2 to 0V
input voltage range and the voltage that results in a
0x0000 output in the 0V to +VREF/2 input voltage range
is the unipolar endpoint overlap. The unipolar endpoint
overlap is positive for the MAX1303, preventing loss of
signal or a dead zone when switching between adja-
cent analog input voltage ranges.
Small-Signal Bandwidth
A 100mVP-P sine wave is applied to the ADC, and the
input frequency is then swept up to the point where the
amplitude of the digitized conversion result has
decreased by -3dB.
Full-Power Bandwidth
A 95% of full-scale sine wave is applied to the ADC,
and the input frequency is then swept up to the point
where the amplitude of the digitized conversion result
has decreased by -3dB.
Common-Mode Rejection Ratio (CMRR)
CMRR is the ability of a device to reject a signal that is
“common” to or applied to both input terminals. The
common-mode signal can be either an AC or a DC sig-
nal or a combination of the two. CMR is expressed in
decibels. Common-mode rejection ratio is the ratio of
the differential signal gain to the common-mode signal
gain. CMRR applies only to differential operation.
Power-Supply Rejection Ratio (PSRR)
PSRR is the ratio of the output-voltage shift to the
power-supply-voltage shift for a fixed input voltage. For
the MAX1303, AVDD1 can vary from 4.75V to 5.25V.
PSRR is expressed in decibels and is calculated using
the following equation:
For the MAX1303, PSRR is tested in bipolar operation
with the analog inputs grounded.
Aperture Jitter
Aperture jitter, tAJ, is the statistical distribution of the
variation in the sampling instant (Figure 19).
Aperture Delay
Aperture delay, tAD, is the time from the falling edge of
SCLK to the sampling instant (Figure 19).
Signal-to-Noise Ratio (SNR)
SNR is computed by taking the ratio of the RMS signal
to the RMS noise. RMS noise includes all spectral com-
ponents to the Nyquist frequency excluding the funda-
mental, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to the RMS noise plus distortion. RMS noise plus
distortion includes all spectral components to the
Nyquist frequency excluding the fundamental and the
DC offset.
Effective Number of Bits (ENOB)
ENOB indicates the global accuracy of an ADC at a
specific input frequency and sampling rate. With an
input range equal to the ADC’s full-scale range, calcu-
late the ENOB as follows:
ENOB
SINAD
.
=
176
602
SINAD dB
Signal
Noise
RMS
(
)
log
=×
20
PSRR dB
VV
OUT
[
]
log
.
(.
)
(.
)
=×
20
525
4 75
525
4 75
tAD
tAJ
INTCLK
(MODE 2)
ANALOG INPUT
TRACK AND HOLD
TRACK
HOLD
SAMPLE INSTANT
SCLK
(MODE 0)
13
14
15
SCLK
(MODE 1)
15
16
10
11
12
Figure 19. Aperture Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1308ECM+T | IC ADC 12BIT 8CH 4MSPS 48LQFP |
| MAX1320ECM+T | IC ADC 14BIT 8CH 2MSPS 48LQFP |
| MAX132EWG+T | IC ADC 18BIT SERIAL 24-SOIC |
| MAX135EPI+ | IC ADC 15BIT PARALLEL 28-DIP |
| MAX1361MEUB+T | IC SYSTEM MON 10BIT 4CH 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1303BEUP+ | 功能描述:模数转换器 - ADC 16-Bit 4Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1303BEUP+T | 功能描述:模数转换器 - ADC 16-Bit 4Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1303BEUP-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX13041ASD/V+ | 功能描述:CAN 接口集成电路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX13041ASD/V+T | 功能描述:CAN 接口集成电路 80V Fault-Protected High-Speed RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。