- 您现在的位置：买卖IC网 > PDF目录9836 > MAX13054ESA+T (Maxim Integrated Products)TXRX CAN 80V FAULT PROT 8-SOIC PDF资料下载
参数资料
| 型号： | MAX13054ESA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | TXRX CAN 80V FAULT PROT 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | CAN |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
MAX13050/MAX13052/MAX13053/MAX13054
Industry-Standard High-Speed CAN
Transceivers with ±80V Fault Protection
12
Maxim Integrated
disabling thermal shutdown once the temperature
drops below +152°C. In thermal shutdown, CANH and
CANL go recessive. After a thermal-shutdown event,
the IC resumes normal operation when the junction
temperature drops below the thermal-shutdown hys-
teresis, and upon the CAN transceiver detecting a ris-
ing edge at TXD.
Applications Information
Reduced EMI and Reflections
In slope-control mode, the MAX13052’s CANH and CANL
outputs are slew-rate limited, minimizing EMI and reduc-
ing reflections caused by improperly terminated cables.
In multidrop CAN applications, it is important to main-
tain a direct point-to-point wiring scheme. A single pair
of wires should connect each element of the CAN bus,
and the two ends of the bus should be terminated with
120
resistors, see Figure 4. A star configuration
should never be used.
Any deviation from the point-to-point wiring scheme
creates a stub. The high-speed edge of the CAN data
on a stub can create reflections back down the bus.
These reflections can cause data errors by eroding the
noise margin of the system.
Although stubs are unavoidable in a multidrop system,
care should be taken to keep these stubs as small as
possible, especially in high-speed mode. In slope-con-
trol mode, the requirements are not as rigorous, but
stub length should still be minimized.
Layout Consideration
CANH and CANL are differential signals and steps
should be taken to insure equivalent parasitic capaci-
MAX13052
RXD
RL = 120
RL = 60
TRANSCEIVER 2
TRANSCEIVER 1
TRANSCEIVER 3
CANH
CANL
TXD
TWISTED PAIR
RL = 60
SPLIT
STUB LENGTH
KEEP AS SHORT
AS POSSIBLE
Figure 4. Multiple Receivers Connected to CAN Bus
CHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
150pF
RC
50M
to 100M
RD
330
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 5. IEC 61000-4-2 Contact Discharge ESD Test Model
tr = 0.7ns to 1ns
30ns
60ns
t
100%
90%
10%
I PEAK
I
Figure 6. IEC 61000-4-2 ESD Test Model Current Waveform
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1483ESA+T | IC TXRX RS485/RS422 LP 8-SOIC |
| MAX1482ESD+T | IC TXRX RS485/RS422 LP 14-SOIC |
| MAX3461CSD+T | IC TXRX RS485/RS422 14-SOIC |
| MAX3462CSA+T | IC TXRX RS485/422 8-SOIC |
| MAX3465CSD+T | IC TXRX RS485/422 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX13055EETI+ | 功能描述:转换 - 电压电平 1.62V to 3.6V 8-Channel High-Speed LLT RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX13055EETI+T | 功能描述:转换 - 电压电平 1.62V to 3.6V 8-Channel High-Speed LLT RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX13055EEVKIT+ | 功能描述:其他开发工具 8 channel high speed LLT RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| MAX13055EEWG+ | 制造商:Maxim Integrated Products 功能描述:1.62V TO 3.6V 8-CHANNEL HIGH-SPEE - Rail/Tube |
| MAX13055EEWG+T | 功能描述:转换 - 电压电平 100Mbps, 8-Ch, Bidir Ectional Level Trans RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
发布紧急采购，3分钟左右您将得到回复。