- 您现在的位置：买卖IC网 > PDF目录1936 > MAX13223EEUP+T (Maxim Integrated Products)IC TXRX RS-232 2TX/2RX 20-TSSOP PDF资料下载
参数资料
| 型号： | MAX13223EEUP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/12页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS-232 2TX/2RX 20-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
MAX13223E
Fault Protection
The MAX13223E is designed to survive faults such as
direct shorts to power supplies, miswiring faults, con-
nector failures, and tool misapplications of the transmit-
ter outputs and receiver inputs to voltages in the ±70V
range without damage. This fault protection is applica-
ble in all modes of the MAX13223E: active, shutdown,
and powered down. Both receivers operate over the
±70V input range, but the termination resistor (RRX,I)
increases when |VR_IN| voltage exceeds ±32V.
A receiver’s input termination resistor reduces to its
nominal value if the input voltage reduces to within the
±24V range. The receiver inputs and transmitter out-
puts are independently fault protected.
±8kV ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electro-
static discharges encountered during handling and
assembly. In using the MAX13223E, C4 must be a 1F
capacitor for the extended ESD protection. The driver
outputs and receiver inputs of the MAX13223E have
extra protection against static electricity. Maxim’s engi-
neers have developed state-of-the-art structures to pro-
tect these pins against ESD of ±8kV without damage.
The ESD structures withstand high ESD in all states:
normal operation, shutdown, and powered down. After
an ESD event, Maxim’s E versions keep working without
latchup, whereas competing RS-232 products can latch
and must be powered down to remove latchup. ESD
protection can be tested in various ways. The transmit-
ter outputs and receiver inputs of this product family are
characterized for protection to the following limits:
1) ±8kV using the Human Body Model
2) ±8kV using the Contact-Discharge Method speci-
fied in IEC 61000-4-2
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 8a shows the Human Body Model and Figure 8b
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.5k
Ω resistor.
IEC 61000-4-2
The IEC 61000-4-2 standard covers ESD testing and
performance of finished equipment. It does not specifi-
cally refer to integrated circuits. The major difference
between tests done using the Human Body Model and
IEC 61000-4-2 is higher peak current in IEC 61000-4-2,
because series resistance is lower in the IEC 61000-4-2
model. Hence, the ESD withstand voltage measured to
IEC 61000-4-2 is generally lower than that measured
using the Human Body Model. Figure 9a shows the IEC
61000-4-2 model and Figure 9b shows the current
waveform for the ±8kV, IEC 61000-4-2, level 4, ESD
Contact-Discharge Method.
±70V Fault-Protected, 3.0V to 5.5V,
2Tx/2Rx RS-232 Transceiver
10
______________________________________________________________________________________
CHARGE-CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
100pF
RC
1M
Ω
RD
1500
Ω
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 8a. Human Body ESD Test Model
IP 100%
90%
36.8%
tRL
TIME
tDL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
Ir
10%
0
AMPERES
Figure 8b. Human Body Current Waveform
相关PDF资料 |
PDF描述 |
|---|---|
| MAX13234EAUP+ | TXRX RS-232 250KBPS 2X2 20TSSOP |
| MAX1329BETL+ | IC DAS 12BIT 300KSPS 40-TQFN-EP |
| MAX13342EEBC+T | IC TXRX USB FS 3WIRE 12-UCSP |
| MAX13410EESA+T | IC TXRX RS-485 LDO/CTRL 8-SOIC |
| MAX1342BETX+ | IC ADC/DAC 12BIT W/FIFO 36WQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1322ECM | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1322ECM+ | 功能描述:模数转换器 - ADC 14-Bit 2Ch 526ksps 3V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1322ECM+T | 功能描述:模数转换器 - ADC 14-Bit 2Ch 526ksps 3V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1322ECM-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX13234EAUP+ | 功能描述:RS-232接口集成电路 3-5.5V 250Kbps RS232 Line Driver/Receiver RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
发布紧急采购，3分钟左右您将得到回复。