- 您现在的位置：买卖IC网 > PDF目录9892 > MAX132CWG+T (Maxim Integrated Products)IC ADC 18BIT SERIAL 24-SOIC PDF资料下载
参数资料
| 型号： | MAX132CWG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT SERIAL 24-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 位数： | 18 |
| 采样率（每秒）： | 100 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个伪差分，双极 |
MAX132
±18-Bit ADC with Serial Interface
12
______________________________________________________________________________________
Command Input Register 1
User-Programmable Output Bits P0 to P3
Command input register 1 always has data bit D0 = 1.
Data bits D4 to D7 of command register 1 control the
states of the user-programmable output pins P0 to P3,
respectively (Table 2). These four outputs can be used
to control an external multiplexer, programmable gain
amplifier, or other devices.
Output Registers
Output data is the sum of system offset (read zero) plus
the results of the external input voltage measurement.
Register 0
Register 0 contains the low-byte (bits B3–B10) conver-
sion data. New data is available after EOC goes high.
Access register 0 by setting RS0 and RS1 to 0.
Register 1
Register 1 contains the high-byte (bits B11–B18) data.
Data is in a twos-complement format where the polarity
bit is a 1 for negative polarity data. Access register 1
by setting control bits RS0 = 1 and RS1 = 0 when writ-
ing to the command input register.
Status Register
Bits B0–B2
The B0, B1, and B2 bits are located in the status regis-
ter. At the end of each conversion these bits are updat-
ed and read back from the status register. For full
18-bit resolution, use bits B0–B2. Average multiple
results to increase accuracy. The polarity bit informa-
tion is necessary to determine if the reading is not in
overrange (Tables 4 and 5).
Integrate Bit
The integrate (INT) bit is set to 1 at the beginning of the
integration phase and becomes 0 at the end. Poll INT
to determine the earliest time the input can be changed
without affecting the conversion.
End-of-Conversion Bit
The end-of-conversion (EOC) bit signals conversion sta-
tus. If EOC is 1, the conversion is complete and the ADC
waits in zero-integrate mode at time = 0000 for the next
start instruction. A conversion cycle has 2048 counts.
EOC becomes 1 at count 0000 and 0 at count 0001.
Collision Bit
The collision bit warns the microprocessor (P) that the
register’s data was changed during the read cycle. A
collision occurs if the internal result latches on the falling
edge of CS, causing the collision bit to be set to 1 on the
rising edge of the next CS. This occurs because these
two pulses are asynchronous. Once the status register is
Table 4. Overrange Values for
Resolution Used
Table 5. Output Values for 16-Bit
Resolution (Offset Corrected)
Bits
Used
B18–B3
B18–B2
B18–B1
Resolution
Bits
±15
±16
±17
B18–B0
±18
Soft Overrange
Start Value
34,880
69,760
139,520
Hard Overrange
Maximum Value
43,805
87,610
175,220
279,040
350,440
Input
+640mV
+576mV
+545mV
Hexadecimal
Reading
+A000
+9000
+8840
Decimal
Counts
+40960*
+36864*
+34880*
+512mV
Comment
+8000
Positive Reference
Voltage
+32768
Positive Full Scale
+448mV
+384mV
+320mV
+7000
+6000
+5000
+28672
+24576
+20480
+256mV
+4000
+16384
+192mV
+128mV
+15V
+3000
+2000
+0001
+12288
+8192
+1
0
+0000
0
-15V
-64mV
-128mV
-FFFF
-F000
-E000
-1
-4096
-8192
-192mV
-D000
-12288
-256mV
-320mV
-384mV
-C000
-B000
-A000
-16384
-20480
-24576
-448mV
-9000
-28672
-512mV
-545mV
-576mV
-8000
-77C0
-7000
-32768
-34880*
-36864*
-640mV
Negative Full Scale
-6000
Negative Reference
Voltage
-40960*
+64mV
+1000
+4096
* Soft Overrange Operation
Note: The MAX132 exhibits additional errors when operating
in the soft overrange area. Operation in this region is not
included in the specifications. The soft overrange values listed
in Table 5 do not include error correction.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX149AEAP+ | IC ADC 10BIT SERIAL 20-SSOP |
| MAX1061ACEI+ | IC ADC 10BIT 250KSPS 28-QSOP |
| IDT72T7295L10BB | IC FIFO 32768X72 10NS 324-BGA |
| V150A28T500BG | CONVERTER MOD DC/DC 28V 500W |
| MX7824KCWG+T | IC ADC 8BIT HS 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX132ENG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX132ENG+ | 功能描述:模数转换器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX132EVKIT-DIP | 功能描述:数据转换 IC 开发工具 MAX132 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX132EWG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX132EWG+ | 功能描述:模数转换器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。