- 您现在的位置：买卖IC网 > PDF目录10207 > MAX13325GUI/V+T (Maxim Integrated Products)IC AUD LINE DVR DL AUTO 28TSSOP PDF资料下载
参数资料
| 型号： | MAX13325GUI/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/21页 |
| 文件大小： | 0K |
| 描述： | IC AUD LINE DVR DL AUTO 28TSSOP |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 线路驱动器，发射器 |
| 应用： | 车载音频 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
16
Maxim Integrated
Dual Automotive, Audio Line Drivers
with I2C Control and Diagnostic
MAX13325/MAX13326
Applications Information
Serial Interface
Writing to the MAX13325/MAX13326 using I2C requires
that first the master sends a START (S) condition fol-
lowed by the device’s I2C address. After the address,
the master sends the register address of the register
that is to be programmed. The master then ends com-
munication by issuing a STOP (P) condition to relinquish
control of the bus, or a Repeated START (Sr) condition to
communicate to another I2C slave (see Figure 1).
Bit Transfer
Each SCL rising edge transfers one data bit. The data
on SDA must remain stable during the high portion of the
SCL clock pulse (see Figure 2). Changes in SDA while
SCL is high are read as control signals (see the START
and STOP Conditions section). When the serial interface
is inactive, SDA and SCL idle high.
Figure 1. I2C Timing
Figure 2. Bit Transfer
Table 17. Overvoltage Diagnostic
tLOW
tF
SDA
SCL
tHD:STA
S
tSU:STA
tHD:DAT
tHIGH
tLOW
tSU:DAT
tF
tHD:STA
tSP
P
tSU:STO
S
Sr
tBUF
tR
SDA
SCL
DATA LINE
STABLE;
DATA VALID
CHANGE OF
DATA ALLOWED
FAULT CONDITION
STATUS REPORT
UNMASK
RECOVERY
Overvoltage
Shutdown
FLAG is asserted low.
In GMASK register, set
MDUMP bit to 1.
See Table 8.
VDD voltage falls below overvoltage
threshold. Cleared on reading the
GFAULT register. Note: 500ms
autoretry in stand-alone mode.
FLAG bit set. See Table 7.
DUMP bit is set in the GFAULT
register. See Table 4.
Left and right channels switch
off and output goes to a
high-impedance state.
Cannot be masked.
Left channel is enabled by setting
the RETRYL bit to 1. Right channel
is enabled by setting the RETRYR
bit to 1. See Table 3.
相关PDF资料 |
PDF描述 |
|---|---|
| CS5368-CQZR | IC ADC 8CH 114DB 216KHZ 48-LQFP |
| MAX5486EUG+T | IC CNTRL VOL STEREO 24TSSOP |
| MAX13326GUI/V+ | IC AUD LINE DVR DL AUTO 28TSSOP |
| ADM101EARMZ-REEL7 | IC TXRX RS-232 SINGLE 5V 10MSOP |
| ADM232LJRZ-REEL | IC TXRX RS-232 2:2 5V LP 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX13326GUI/V+ | 功能描述:缓冲器和线路驱动器 Dual Audio Line Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MAX13326GUI/V+T | 功能描述:缓冲器和线路驱动器 Dual Audio Line Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MAX13330GEE/V+ | 功能描述:音频放大器 DirectDrive Head Phone Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX13330GEE/V+T | 功能描述:音频放大器 DirectDrive Head Phone Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX13331EVKIT+ | 功能描述:音频 IC 开发工具 MAX13331 DirectDrive Eval Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。