参数资料
| 型号： | MAX13335EEVKIT# |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/12页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT |
| 标准包装： | 1 |
| 系列： | * |
MAX13335E Evaluation Kit
Evaluates: MAX13335E /MAX13336E
Quick Start
8)
Connect the oscilloscope channel 1 to the OUTL
PCB pad.
?
?
?
?
Recommended Equipment
MAX13335E EV kit (USB cable included)
Function generator
Oscilloscope
User-supplied Windows XP, Windows Vista, or
Windows 7 PC with an available USB port
9)
10)
Connect the oscilloscope channel 2 to the OUTR
PCB pad.
Connect a USB cable between the PC and the Mini-
USB port on the EV kit. A New Hardware Found
window pops up when installing the USB driver
for the first time. If a window that is similar to the
one described above is not seen after 30s, remove
Note: In the following sections, software-related items are
identified by bolding. Text in bold refers to items directly
from the EV kit software. Text in bold and underlined
the USB cable from the board and reconnect it.
Administrator privileges are required to install the
USB device driver on Windows.
refers to items from the Windows operating system.
Procedure
The EV kit is fully assembled and tested. Follow the
steps below to verify board operation. Do not turn on
the power supply until all connections are completed.
1) Visit www.maxim-ic.com/evkitsoftware to down-
load the latest version of the EV kit software,
13335ERxx.ZIP. Save the EV kit software to a
temporary folder and uncompress the ZIP file.
2) Install the EV kit software on your computer by run-
ning the INSTALL.EXE program inside the temporary
folder. The program files are copied and icons are
created on the desktop and in the Windows Start |
Programs| Maxim EVKIT Software menu.
11)
12)
13)
14)
15)
Follow the directions of the Found New Hardware
window to install the USB device driver. Refer to the
USB_Driver_Help_200.PDF document included with
the software for additional information.
Start the EV kit software by opening its icon on
the desktop or in the Start | Programs | Maxim
EVKITSoftware menu. The EV kit software main
window appears, as shown in Figure 1.
Wait while the software connects to the EV kit. Once
the connection is established, the bottom-left status
bar displays Hardware: Connected .
Enable the function generator.
Verify that the oscilloscope channels 1 and 2 each
output a 1kHz, 2V P-P , sine wave with 0V offset.
3)
4)
5)
6)
7)
Verify that all jumpers are in their default positions,
as shown in Table 1.
Set the function generator output to high impedance
and to output a 1kHz, 10V P-P , sine wave with 0V
offset. Disable the function generator.
Connect the function generator output to the
INPUTL+ and INPUTR+ PCB pads.
Connect the function generator ground to the GND
PCB pad.
Connect the INPUTL- and INPUTR- PCB pads to the
Detailed Description of Software
Graphical User Interface (GUI)
The MAX13335E EV kit software GUI provides a
convenient way to test the features of the MAX13335E IC.
Figure 1 shows the EV kit software’s main window. The
EV kit software main window divides the EV kit functions
into logical blocks. Actions on this software window
generate I 2 C commands to update the IC’s internal
memory registers.
GND PCB pad.
Table 1. Jumper Positions (JU1–JU5)
JUMPER
JU1
JU2
JU3
JU4
JU5
SHUNT POSITION
1-2*
2-3
1-2*
Pin 1
1-2*
Pin 1
1-2*
Pin 1
1-2*
Pin 1
DESCRIPTION
On-board VDD supply. Connects the on-board USB +5V to VDD.
External VDD supply. Externally supply VDD with +3.3V or +5V.
On-board VL supply. Connects the on-board VDD to the logic-level translator output supply VL.
External VL supply. Externally supply VL with +3.3V or +5V.
On-board I 2 C. Connects the IC’s INT output to the on-board microcontroller.
User-supplied I 2 C. Connects the IC’s INT output to the user-supplied microcontroller.
On-board I 2 C. Connects the on-board SDA signal to the SDA PCB pad.
User-supplied I 2 C. Open the jumper and apply the SDA signal to the SDA PCB pad.
On-board I 2 C. Connects the on-board SCL signal to the SCL PCB pad.
User-supplied I 2 C. Open the jumper and apply the SCL signal to the SCL pad.
* Default position.
_________________________________________________________________ Maxim Integrated Products 3
相关PDF资料 |
PDF描述 |
|---|---|
| MAX13487EEVKIT# | KIT EVAL FOR MAX13487E |
| MAX1385EVKIT+ | EVAL KIT FOR MAX1385 |
| MAX14527ETA+T | IC OVERVOLTAGE PROTECTOR 8TDFN |
| MAX14562ETA+T | IC OVP 36V PROTECT W/REG 8-TDFN |
| MAX14830EVKIT# | EVAL KIT QUAD SER UART MAX14830 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX13335EEVKIT# | 功能描述:放大器 IC 开发工具 MAX13335E Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX13335EEVKIT+ | 功能描述:放大器 IC 开发工具 MAX13335E Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX13335EGEE/V+ | 功能描述:音频放大器 Differential Audio Input Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX13335EGEE/V+T | 功能描述:音频放大器 Differential Audio Input Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| MAX13336EGEE/V+ | 功能描述:音频放大器 Differential Audio Input Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。