- 您现在的位置：买卖IC网 > PDF目录1936 > MAX13448EESD+T (Maxim Integrated Products)IC TXRX RS485 FULL DUPLEX 14SOIC PDF资料下载
参数资料
| 型号： | MAX13448EESD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/14页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485 FULL DUPLEX 14SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS485 |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
MAX13448E
±80V Fault-Protected Full-Duplex
RS-485 Transceiver
12
______________________________________________________________________________________
CHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
100pF
RC
1M
Ω
RD
1500
Ω
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 8a. Human Body ESD Test Model
IP 100%
90%
36.8%
tRL
TIME
tDL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
Ir
10%
0
AMPS
Figure 8b. Human Body Current Waveform
receiver threshold between -50mV and -200mV. If the
differential receiver input voltage (A - B) is greater than
or equal to -50mV, RO is logic-high. If A - B is less than
or equal to -200mV, RO is logic-low. In the case of a
terminated bus with all transmitters disabled, the
receiver’s differential input voltage is pulled to 0V by
the termination. With the receiver thresholds of the
MAX13448E, this results in a logic-high with a 50mV
minimum noise margin. The -50mV to -200mV threshold
complies with the ±200mV EIA/TIA-485 standard.
±8kV ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electro-
static discharges encountered during handling and
assembly. The driver outputs and receiver inputs of the
MAX13448E have extra protection against static elec-
tricity. Maxim’s engineers have developed state-of-the-
art structures to protect these pins against ESD of ±8kV
without damage. The ESD structures withstand high
ESD in all states: normal operation, shutdown, and
powered down. After an ESD event, the MAX13448E
keeps working without latchup or damage. ESD protec-
tion can be tested in various ways. The transmitter out-
puts and receiver inputs of the MAX13448E are
characterized for protection to the following limits:
±8kV using the Human Body Model
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 8a shows the Human Body Model, and Figure
8b shows the current waveform it generates when dis-
charged into a low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.5k
Ω resistor.
Driver Output Protection
Two mechanisms prevent excessive output current and
power dissipation caused by faults or by bus con-
tention. The first, a foldback current limit on the output
stage, provides immediate protection against short
circuits over the whole common-mode voltage range
(see the
Typical Operating Characteristics). The sec-
ond, a thermal-shutdown circuit, forces the driver out-
puts into a high-impedance state if the die temperature
exceeds +160°C (typ).
Hot-Swap Capability
Hot-Swap Inputs
When circuit boards are inserted into a powered back-
plane, disturbances to the data bus can lead to data
errors. Upon initial circuit-board insertion, the data
communication processor undergoes its own power-up
sequence. During this period, the processor’s logic-
output drivers are high impedance and are unable to
drive the DE input of the device to a defined logic level.
Leakage currents up to ±10A from the high-imped-
ance state of the processor’s logic drivers could cause
standard CMOS enable inputs of a transceiver to drift to
an incorrect logic level. Additionally, parasitic circuit-
board capacitance could cause coupling of VCC or
GND to the enable inputs. Without the hot-swap capa-
bility, these factors could improperly enable the trans-
ceiver’s driver or receiver.
When VCC rises, an internal pulldown circuit holds DE
low. After the initial power-up sequence, the pulldown
circuit becomes transparent, resetting the hot-swap
tolerable input.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX13450EAUD+ | TXRX RS-485 14TSSOP |
| MAX13482EETE+T | IC TXRX USB ESD PROT 16-TQFN |
| MAX13486EESA+ | IC TXRX RS485/422 8-SOIC |
| MAX13488EESA+T | IC TXRX RS485/RS422 8-SOIC |
| MAX1358BETL+W | DAS 16BIT DUAL 10:1 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX13450EAUD+ | 功能描述:RS-485接口IC Half/Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX13450EAUD+T | 功能描述:RS-485接口IC Half/Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX13451EAUD+ | 功能描述:RS-485接口IC Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX13451EAUD+T | 功能描述:RS-485接口IC Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1346BETX | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
发布紧急采购，3分钟左右您将得到回复。