- 您现在的位置：买卖IC网 > Datasheet目录471 > MAX1385BUTM+ (Maxim Integrated)IC RF LDMOS BIAS CNTRLR 48-TQFN Datasheet资料下载
参数资料
| 型号： | MAX1385BUTM+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 25/52页 |
| 文件大小： | 0K |
| 描述： | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 功能： | 偏压控制器 |
| RF 型： | 通用 |
| 次要属性： | 双 RF LDMOS 带 I2C/SPI 接口 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Dual RF LDMOS Bias Controllers
with I 2 C/SPI Interface
MEASUREMENT VALUE
(TEMPERATURE OR CURRENT)
HIGH THRESHOLD
BUILT-IN HYSTERESIS
BUILT-IN HYSTERESIS
LOW THRESHOLD
TIME
ALARM OUTPUT
OUTPUT-
COMPARATOR MODE
(ACTIVE LOW)
OUTPUT-
INTERRUPT MODE
(ACTIVE LOW)
FLAG REGISTER
READ
Figure 8. Window-Threshold-Mode Timing Diagram
FLAG REGISTER FLAG REGISTER
READ READ
TIME
In single-conversion mode (CKSEL = 11), the BUSY
signal remains high until the ADC has completed the
current conversion (not the entire scan, just the current
conversion), the data has been moved into the FIFO,
and the alarm limits for the channel have been checked
(if enabled). In multiple-conversion mode (CKSEL = 01
or CKSEL = 00), the BUSY signal remains high until all
channels have been scanned and the data from the
final channel has been moved into the FIFO and
checked for alarm limits (if enabled). In continuous-con-
version mode (CONCONV = 1), the BUSY signal does
not go high as a result of ADC conversions; however,
BUSY does go high when CONCONV is removed and
remains high until the current scan is complete and the
ADC sequence halts.
After commanding any of the DAC autocalibration compo-
nents, wait for BUSY to go low before setting OSCPD to 1.
Alarm Modes
The MAX1385/MAX1386 contain several programmable
modes for configuring outputs ALARM, SAFE1, and
SAFE2 behavior. Window-threshold mode allows SAFE_
to assert when the temperature/current is too high or
too low (outside the window). Hysteresis-threshold
mode allows SAFE_ to assert when the temperature/
current is too high, and then to deassert when the tem-
perature/current falls back to an appropriate level.
ALARM asserts when SAFE1 and/or SAFE2 asserts.
Program ALARM for output-comparator mode to stay
asserted after an alarm condition until temperature/cur-
rent levels are back below programmed thresholds.
Program ALARM for output-interrupt mode to stay
asserted after an alarm condition until the Flag register
is read.
Window-Threshold Mode
In window-threshold mode, ADC readings of
current/temperature are compared to the configured
current/temperature low/high thresholds that are pro-
grammed to cause an alarm condition. If an ADC read-
ing falls out of the configured window and ALARM is
configured for output-comparator mode, ALARM
asserts until the current/temperature reading falls back
into the window (past the built-in hysteresis). If an ADC
reading falls out of the configured window and ALARM
is configured for output-interrupt mode, ALARM asserts
until the Flag register is read. Set the amount of built-in
hysteresis from 8 LSBs to 64 LSBs (see the ALMSCFG
(Read/Write) section). See Figures 7 and 8.
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
| MAX1470EVKIT-315 | EVAL KIT FOR MAX1470 315MHZ |
| MAX1471EVKIT-315 | EVAL KIT FOR MAX1471 315MHZ |
| MAX1472EVKIT-433# | EVAL KIT MAX1472 |
| MAX1473EVKIT-433 | EVAL KIT MAX1473 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1385BUTM+ | 功能描述:射频放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX1385BUTM+T | 功能描述:射频放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX1385EVC16 | 功能描述:放大器 IC 开发工具 MAX1385 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX1385EVKIT+ | 功能描述:射频开发工具 MAX1385 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX1386AETM+ | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。