- 您现在的位置：买卖IC网 > PDF目录11669 > MAX1452EAE+ (Maxim Integrated Products)IC SENSOR SIGNAL COND 16-SSOP PDF资料下载
参数资料
| 型号： | MAX1452EAE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/25页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR SIGNAL COND 16-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 76 |
| 类型： | 信号调节器 |
| 输入类型： | 模拟 |
| 输出类型： | 模拟 |
| 接口： | 串行 |
| 电流 - 电源： | 2.5mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
MAX1452
Low-Cost Precision Sensor
Signal Conditioner
8
Maxim Integrated
Linear and Nonlinear
Temperature Compensation
Writing 16-bit calibration coefficients into the offset TC
and FSOTC registers compensates first-order tempera-
ture errors. The piezoresistive sensor is powered by a
current source resulting in a temperature-dependent
bridge voltage due to the sensor's temperature resis-
tance coefficient (TCR). The reference inputs of the off-
set TC DAC and FSOTC DAC are connected to the
bridge voltage. The DAC output voltages track the
bridge voltage as it varies with temperature, and by
varying the offset TC and FSOTC digital code a portion
of the bridge voltage, which is temperature dependent,
is used to compensate the first order temperature
errors.
The internal feedback resistors (RISRC and RSTC) for
FSO temperature compensation are optimized to 75k
Ω
for silicon piezoresistive sensors. However, since the
required feedback resistor values are sensor dependent,
external resistors may also be used. The internal resis-
tors selection bit in the configuration register selects
between internal and external feedback resistors.
To calculate the required offset TC and FSOTC com-
pensation coefficients, two test-temperatures are need-
ed. After taking at least two measurements at each
temperature, calibration software (in a host computer)
calculates the correction coefficients and writes them to
the internal EEPROM.
With coefficients ranging from 0000hex to FFFFhex and
a +5V reference, each DAC has a resolution of 76V.
Two of the DACs (offset TC and FSOTC) utilize the sen-
sor bridge voltage as a reference. Since the sensor
bridge voltage is approximately set to +2.5V the FSOTC
and offset TC exhibit a step size of less than 38V.
For high accuracy applications (errors less than
0.25%), the first-order offset and FSO TC error should
be compensated with the offset TC and FSOTC DACs,
and the residual higher order terms with the lookup
table. The offset and FSO compensation DACs provide
unique compensation values for approximately 1.5°C of
temperature change as the temperature indexes the
address pointer through the coefficient lookup table.
Changing the offset does not effect the FSO, however
changing the FSO affects the offset due to nature of the
bridge. The temperature is measured on both the
MAX1452 die and at the bridge sensor. It is recom-
mended to compensate the first-order temperature
errors using the bridge sensor temperature.
Typical Ratiometric
Operating Circuit
Ratiometric output configuration provides an output that
is proportional to the power supply voltage. This output
can then be applied to a ratiometric ADC to produce a
digital value independent of supply voltage.
Ratiometricity is an important consideration for battery-
operated instruments, automotive, and some industrial
applications.
The MAX1452 provides a high-performance ratiometric
output with a minimum number of external components
(Figure 2). These external components include the fol-
lowing:
One supply bypass capacitor.
One optional output EMI suppression capacitor.
Two optional resistors, RISRC and RSTC, for special
sensor bridge types.
Figure 2. Basic Ratiometric Output Configuration
MAX1452
+5V VDD
OUT
GND
RSTC
RISRC
0.1
μF 0.1μF
INM
TEST VSS
INP
7
9
2
16
1
8
3
BDR
VDDF
OUT
5
6
4
FSOTC
ISRC
SENSOR
VDD
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1452CAE+ | IC SENSOR SIGNAL COND 16-SSOP |
| DS1877T+ | IC CTLR/MON SFP 1-2CH 28TQFN |
| MAX7360ETL+ | IC CTRLR KEY-SW I2C 40TQFN-EP |
| DS1878T+ | IC CTLR SFP W/DGTL LDD RX 28TQFN |
| MAX9621AUB+ | IC HALL EFFECT SENSOR 10UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1452EAE+ | 功能描述:板上安装温度传感器 Precision Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1452EAE+C8H | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1452EAE+T | 功能描述:板上安装温度传感器 Precision Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1452EAE-T | 功能描述:板上安装温度传感器 Precision Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1452EVKIT-CS | 功能描述:数据转换 IC 开发工具 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。