参数资料
型号: MAX14535EEVB+
厂商: Maxim Integrated Products
文件页数: 11/13页
文件大小: 0K
描述: IC SWITCH DPDT 10UTQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 90
功能: 开关
电路: 1 x DPDT
导通状态电阻: 350 毫欧
电压电源: 单电源
电压 - 电源,单路/双路(±): 2.4 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-UFQFN
供应商设备封装: 10-UTQFN(1.4x1.8)
包装: 管件
MAX14535E–MAX14539E
Low-Resistance DPDT Switches
with Negative Rail
_______________________________________________________________________________________
7
Pin Description
PIN
NAME
FUNCTION
1
CB
Digital Control Input. Drive CB low to connect COM_ to NC_. Drive CB high to connect COM_ to NO_.
2EN
Active-High Enable Input. Drive EN high for normal operation. Drive EN low to put switches in high
impedance. Do not apply negative signals to NO_ or NC_ when EN is low (MAX14537E/MAX14538E).
3
NO2
Normally Open Terminal for Switch 2
4
COM2
Common Terminal for Switch 2
5
NC2
Normally Close Terminal for Switch 2
6
GND
Ground
7VCC
Positive Supply Voltage Input. Bypass VCC to GND with a 0.1F capacitor as close as possible to the
device.
8
NC1
Normally Close Terminal for Switch 1
9
COM1
Common Terminal for Switch 1
10
NO1
Normally Open Terminal for Switch 1
Detailed Description
The MAX14535E–MAX14539E are low on-resistance
and high ESD-protected single DPDT switches that
operate from a +2.4V to +5.5V supply and are
designed to multiplex AC-coupled analog signals.
These switches combine the low on-capacitance (CON)
and low on-resistance (RON) necessary for high-perfor-
mance switching applications. The negative signal
capability of the analog channel allows signals below
ground to pass through without distortion.
Analog Signal Levels
The MAX14535E
MAX14539E are bidirectional, allow-
ing NO_, NC_, and COM_ to be configured as either
inputs or outputs. Note that NC_ and NO_ are only pro-
tected against ESD up to ±2kV (Human Body Model)
and may require additional ESD protection if used as
outputs. These devices feature a charge pump that
generates a negative supply to allow analog signals as
low as -1.5V to pass through NO_, NC_, or COM_. This
allows AC-coupled signals that drop below ground to
pass even when operating from a 3.0V to 5.5V supply.
For the MAX14537E/MAX14538E, the negative charge
pump is controlled by the enable input and is active
when EN is high. When EN is driven low, the negative
charge pump is disabled, which puts the devices in the
lowest possible current consumption, and the signal
range is 0 to VCC. The negative charge pump is always
active for the MAX14535E/MAX14536E/MAX14539E,
therefore, a negative signal (at most -1.5V) can be
applied through NC_, NO_, or COM_, even when EN is
driven low. A negative rail signal (signal voltage < 0)
must not be applied to the switch unless the negative
charge pump is active.
Digital Control Input
The MAX14535E
MAX14539E provide a single-bit con-
trol logic input, CB. CB controls the switch position as
shown in the
Functional Diagrams. Drive CB rail-to-rail
to minimize power consumption.
Enable Input
The MAX14535E
MAX14539E feature a shutdown
mode that reduces the supply current (less than 1A
for MAX14537E/MAX14538E) and places the switches
in high impedance. Drive EN low to place the device in
shutdown mode. Drive EN high for normal operation.
Shunt Resistors
(MAX14535E/MAX14537E/MAX14539E)
When EN is high, the shunt resistors are controlled by
CB. When CB is low, NC_ is connected to COM_ and
NO_ is connected to shunt resistors. When CB is high,
NO_ is connected to COM_ and NC_ is connected to
shunt resistors (MAX14539E). When EN is low, all the
switches are open and all the shunt resistors are active.
Click-and-Pop Suppression
The 500
shunt resistors on the MAX14535E/
MAX14537E/MAX14539E automatically discharge any
capacitance at the NO_ terminals (or NC_ terminals,
MAX14539E) when they are unconnected from COM_.
This reduces audio click-and-pop sounds that may
occur when switching between capacitively coupled
audio sources.
相关PDF资料
PDF描述
VE-21B-IY-F1 CONVERTER MOD DC/DC 95V 50W
C8051F311-GMR IC 8051 MCU 16K FLASH 28MLP
VE-B14-IY-F4 CONVERTER MOD DC/DC 48V 50W
MAX4885EETG+T IC MULTIPLEXER 2X1 24TQFN
VE-B14-IY-F3 CONVERTER MOD DC/DC 48V 50W
相关代理商/技术参数
参数描述
MAX14535EEVB+ 功能描述:IC SWITCH DPDT 10UTQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关,多路复用器,多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:14 系列:- 功能:多路复用器 电路:1 x 16:1 导通状态电阻:175 欧姆 电压电源:单/双电源 电压 - 电源,单路/双路(±):4.5 V ~ 30 V,±4.5 V ~ 20 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 产品目录页面:1419 (CN2011-ZH PDF)
MAX14535EEVB+T 功能描述:交换机 IC 开发工具 Low-Resistance DPDT Switch w/Neg Rail RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V
MAX14535EEVKIT+ 功能描述:交换机 IC 开发工具 MAX14535E Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V
MAX14536EEVB+ 功能描述:IC SWITCH DPDT 10UTQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关,多路复用器,多路分解器 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:- 电路:2 x SPST 导通状态电阻:20 欧姆 电压电源:单电源 电压 - 电源,单路/双路(±):3 V ~ 5.5 V 电流 - 电源:4.1mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP(3x3) 包装:带卷 (TR)
MAX14536EEVB+T 功能描述:交换机 IC 开发工具 Low-Resistance DPDT Switch w/Neg Rail RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V