- 您现在的位置：买卖IC网 > PDF目录383322 > MAX1481-MAX1486 (Maxim Integrated Products, Inc.) Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package PDF资料下载
参数资料
| 型号： | MAX1481-MAX1486 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package |
| 中文描述： | 软件可选，Half-/Full-Duplex，摆率限制，12Mbps的，RS-485/RS-422收发器在レ最大包 |
| 文件页数： | 10/16页 |
| 文件大小： | 184K |
| 代理商： | MAX1481-MAX1486 |
M
Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited,
12Mbps, RS-485/RS-422 Transceivers in μMAX Package
10
______________________________________________________________________________________
_______________Detailed Desc ription
The MAX1481/MAX1484/MAX1485/MAX1486 high-
speed transceivers for RS-485/RS-422 communication
contain one driver and one receiver. The MAX1481/
MAX1485 feature reduced-slew-rate drivers that mini-
mize EMI and reduce reflections caused by improperly
terminated cables, allowing error-free data transmission
up to 250kbps. The MAX1484/MAX1486 driver slew
rates are not limited, making transmission speeds up to
12Mbps possible.
These transceivers are designed to operate on a +5V
single supply and typically draw 300μA of supply cur-
rent when unloaded or fully loaded with the drivers dis-
abled. The MAX1481 has a shutdown mode in which
supply current is typically reduced to 0.1μA.
Drivers are output short-circuit current limited and are
protected against excessive power dissipation by ther-
mal-shutdown circuitry that places the driver outputs
into a high-impedance state.
All devices have a 1/8-unit-load receiver input imped-
ance that allows up to 256 transceivers on the bus. The
MAX1481/MAX1484 are designed for full-duplex com-
munications. The H/
F
pin on the MAX1485/MAX1486
allows the user to select between half-duplex or full-
duplex operation (Figure 4).
MAX 1485/MAX 1486
Half-/Full-Duplex Mode Operation
The MAX1484/MAX1485 can operate in full- or half-
duplex mode. Drive the H/
F
pin low or connect it to
GND for full-duplex operation, or drive it high for half-
duplex operation. In full-duplex mode, the pin configu-
ration of the driver and receiver is the same as a
MAX1481 (Figure 1).
__________Applic ations Information
256 T ransc eivers on the Bus
The standard RS-485 receiver input impedance is 12k
(1-unit load), and the standard driver can drive up to
32-unit loads. The MAX1481/MAX1484/MAX1485/
MAX1486 transceivers have a 1/8-unit-load receiver
input impedance (96k
), allowing up to 256 trans-
ceivers to be connected in parallel on one communica-
tion line. Connect any combination of these devices
and/or other RS-485 transceivers totaling 32-unit loads
or less.
Reduc ed EMI and Reflec tions
The MAX1481/MAX1485 are slew-rate limited, minimiz-
ing EMI and reducing reflections caused by improperly
terminated cables. Figure 14 shows the driver output
waveform and its Fourier analysis of a 20kHz signal
transmitted by a MAX1484. High-frequency harmonic
components with large amplitudes are evident. Figure
15 shows the same signal displayed for a MAX1481
transmitting under the same conditions. Figure 15’s
high-frequency harmonic components are much lower
in amplitude compared to Figure 14’s, significantly
reducing potential EMI.
In general, a transmitter’s rise time relates directly to
the length of an unterminated stub, which can be dri-
ven with only minor waveform reflections. The following
equation expresses this relationship conservatively:
Length = t
RISE
/ (10 x 1.5ns/ft)
where t
RISE
is the transmitter’s rise time.
For example, the MAX1481’s rise time is typically
500ns, which results in excellent waveforms with a stub
length up to 33 feet. A system may work well with
longer unterminated stubs, even with severe reflec-
tions, if the waveform settles out before the UART
samples them.
MAX1485
MAX1486
B
DI
DE
RO
V
CC
GND
A
Z
Y
H/F
Figure 4. MAX1485/MAX1486 Functional Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1481CUB | Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package |
| MAX1481EUB | Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package |
| MAX1484CUB | Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package |
| MAX1484EUB | Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package |
| MAX1485EUB | Software-Selectable, Half-/Full-Duplex, Slew-Rate-Limited, 12Mbps, RS-485/RS-422 Transceivers in レMAX Package |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX14820EETG+T | 制造商:Maxim Integrated Products 功能描述: |
| MAX14820ETG+ | 功能描述:输入/输出控制器接口集成电路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MAX14820ETG+T | 功能描述:输入/输出控制器接口集成电路 IO-Link Device Transceiver RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MAX14820EVKIT# | 功能描述:界面开发工具 MAX14820/21 EVAL KIT RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX14821ETG+ | 功能描述:输入/输出控制器接口集成电路 NEW RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。