参数资料
型号: MAX1490EACPG+
厂商: Maxim Integrated Products
文件页数: 19/19页
文件大小: 0K
描述: IC RS485/RS422 DATA INTRFC 24DIP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 16
类型: 收发器
驱动器/接收器数: 1/1
规程: RS422,RS485
电源电压: 4.5 V ~ 5.5 V
安装类型: 通孔
封装/外壳: 24-DIP(0.600",15.24mm)
供应商设备封装: 24-PDIP
包装: 管件
产品目录页面: 1403 (CN2011-ZH PDF)
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
_______________________________________________________________________________________
9
Detailed Description
The MAX1480EA/MAX1480EC/MAX1490EA/MAX1490EB
are complete, electrically isolated, RS-485/RS-422 data-
communications interface solutions. Transceivers, opto-
couplers, a power driver, and a transformer in one
standard 28-pin DIP package (24-pin package for the
MAX1490EA/MAX1490EB) provide a complete inter-
face. Signals and power are internally transported
across the isolation barrier (Figures 1, 2). Power is
transferred from the logic side (nonisolated side) to the
isolated side of the barrier through a center-tapped
transformer. Signals cross the barrier through high-
speed optocouplers. A single +5V supply on the logic
side powers both sides of the interface. The
MAX1480EA/MAX1480EC offer half-duplex communica-
tions while the MAX1490EA/MAX1490EB feature full-
duplex communication. The functional input/output
relationships are shown in Tables 3 through 6.
The MAX1480EC/MAX1490EB feature reduced-slew-rate
drivers that minimize EMI and reduce reflections caused
by improperly terminated cables, allowing error-free
transmission at data rates up to 160kbps. The
MAX1480EA/MAX1490EA driver slew rate is not limited,
allowing transmission rates up to 2.5Mbps.
The MAX1480EC/MAX1490EB shutdown feature reduces
supply current to as low as 0.2A by using the SD pin (see
Low-Power Shutdown Mode section).
Drivers are short-circuit current limited and are protect-
ed against excessive power dissipation by thermal
shutdown circuitry that puts the driver outputs into a
high-impedance state. The receiver input has a fail-safe
feature that guarantees a logic-high RO (logic-low RO)
output if the input is open circuit.
On the MAX1480EA/MAX1480EC, the driver outputs are
enabled by bringing DE
high. Driver-enable time is typi-
cally 1.0s. Allow time for the devices to be
enabled before sending data (see Typical Operating
Characteristics). When enabled, driver outputs function
as line drivers. Driver outputs are high impedance when
DE
is low. When outputs are high impedance, they func-
tion as line receivers.
The MAX1480EA/MAX1480EC/MAX1490EA/MAX1490EB
withstand 1260VRMS (1min) or 1520VRMS (1s). The logic
inputs can be driven from TTL/CMOS logic with a series
resistor, and the received data output can directly drive
TTL or CMOS-logic families with only a resistive pullup.
Low-Power Shutdown Mode
The SD pin shuts down the oscillator on the internal power
driver. With the primary side in shutdown, no power is
transferred across the isolation barrier. The DI and DE
optocouplers, however, still consume current if the drive
signals on the nonsolated side are low. Therefore, leave
DI
and DE high or floating when in shutdown mode.
Under these conditions, the MAX1480EC/MAX1490EB
supply current is reduced to as low as 0.2A.
___________________________________________________Pin Description (continued)
Note: For DE
and DI pin descriptions, see Detailed Block Diagram and Typical Application Circuit (Figure 1 for MAX1480EA/
MAX1480EC, Figure 2 for MAX1490EA/MAX1490EB).
Internal Connections. Leave these pins unconnected.
AC2, AC1
23, 24
27, 28
26
22
ISO VCC1
Isolated Supply Voltage Source
Inverting Driver Output and Inverting Receiver Input
B
25
Isolated Receiver-Output Drive. Connect to ISO RO LED through a resistor (see
Table 1 for MAX1480EA/MAX1480EC, Table 2 for MAX1490EA/MAX1490EB).
ISO RO DRV
21
24
23
A
Noninverting Driver Output and Noninverting Receiver Input
Isolated Driver Input. Connect to ISO DI DRV for normal operation.
ISO DI IN
22
Isolated Driver-Enable Input. Connect to ISO DE DRV for normal operation.
ISO DE IN
21
Noninverting Receiver Input
A
20
Inverting Receiver Input
B
19
Inverting Driver Output
Z
18
Noninverting Driver Output
Y
17
FUNCTION
NAME
MAX1490EA/
MAX1490EB
MAX1480EA/
MAX1480EC
PIN
相关PDF资料
PDF描述
MAX1294BEEI+ IC ADC 12BIT 420KSPS 28-QSOP
MAX1295BEEI+ IC ADC 12BIT 265KSPS 28-QSOP
MS3116P10-98SX CONN PLUG 6POS STRAIGHT W/SCKT
MAX1265BEEI+ IC ADC 12-BIT 265KSPS 28-QSOP
VE-24H-IW-F3 CONVERTER MOD DC/DC 52V 100W
相关代理商/技术参数
参数描述
MAX1490EACPG+ 功能描述:RS-422/RS-485 接口 IC Isolated RS-485/422 Data Interface RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube
MAX1490EAEPG 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube
MAX1490EAEPG+ 功能描述:RS-422/RS-485 接口 IC Isolated RS-485/422 Data Interface RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube
MAX1490EBCPG 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube
MAX1490EBCPG+ 功能描述:RS-422/RS-485 接口 IC Isolated RS-485/422 Data Interface RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube