- 您现在的位置：买卖IC网 > PDF目录10565 > MAX1496EPI+ (Maxim Integrated Products)IC ADC 3.5DIGIT LED DRVR 28-DIP PDF资料下载
参数资料
| 型号： | MAX1496EPI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 3.5DIGIT LED DRVR 28-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 14 |
| 位数： | 3.5 位 |
| 采样率（每秒）： | 5 |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 28-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 28-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
| 产品目录页面： | 1397 (CN2011-ZH PDF) |
MAX1447/MAX1496/MAX1498
3.5- and 4.5-Digit, Single-Chip ADCs
with LED Drivers
18
______________________________________________________________________________________
Selecting Segment Current
A resistor from ISET to ground sets the current for each
LED segment. See Table 5 for more detail. Use the fol-
lowing formula to set the segment current:
RISET values below 25k
increase the ISEG. However,
the internal current-limit circuit limits the ISEG to less than
30mA. At higher ISEG values, proper operation of the
device is not guaranteed. In addition, the power dissipat-
ed may exceed the package power-dissipation limit.
Choosing Supply Voltage to Minimize
Power Dissipation
The MAX1447/MAX1496/MAX1498 drive a peak current
of 25.5mA into LEDs with a 2.2V forward voltage drop
when operated from a supply voltage of at least 3.0V.
Therefore, the minimum voltage drop across the inter-
nal LED drivers is (3.0V - 2.2V) = 0.8V. The MAX1447/
MAX1496/MAX1498 sink (8 x 25.5mA = 204mA) when
the outputs are operating and the LED segment drivers
are at full current. For a 3.3V supply, the MAX1447/
MAX1496/MAX1498 dissipate (3.3V - 2.2V) x 204 =
224.4mW. If a higher supply voltage is used, the driver
absorbs a higher voltage, and the driver’s power dissi-
pation increases accordingly. However, if the LEDs
used have a higher forward voltage drop than 2.2V, the
supply voltage must be raised accordingly to ensure
that the driver always has at least 0.8V headroom.
For a VLED supply voltage of 2.7V, the maximum LED
forward voltage is 1.9V to ensure 0.8V driver headroom.
The voltage drop across the drivers with a nominal +5V
supply (5.0V - 2.2V = 2.8V) is almost three times the
drop across the drivers with a nominal 3.3V supply
(3.3V - 2.2V = 1.1V). Therefore, the driver’s power dissi-
pation increases three times. The power dissipation in
the part causes the junction temperature to rise accord-
ingly. In the high ambient temperature case, the total
junction temperature may be very high (>+125°C). At
higher junction temperatures, the ADC performance
degrades. To ensure the dissipation limit for the
MAX1447/MAX1496/MAX1498 is not exceeded and the
ADC performance is not degraded, a diode can be
inserted between the power supply and VLED.
Computing Power Dissipation
The following can be used to compute power dissipation:
PD = (VLED x IVLED ) + (VLED - VDIODE)
(DUTY x ISEG x N) + VSUPPLY x ISUPPLY
VLED = LED driver supply voltage
IVLED = VLED bias current
VDIODE = LED forward voltage
DUTY = segment ON time during each digit ON time
ISEG = segment current set by RISET
N = number of segments driven (worst case is eight)
VSUPPLY = supply voltage of the part
ISUPPLY = supply current from VDD for the MAX1496 or
AVDD + DVDD for the MAX1447/MAX1498.
Dissipation Example
For ISEG = 25.5mA, N = 8, DUTY = 127 / 128, VDIODE =
1.5V at 25.5mA, VLED = VSUPPLY = 5.25V:
PD = (5.25 x 2mA) + (5.25V - 1.5) [(127 / 128)
x 25.5mA x 8)] + 5.25 x 1.080mA
PD = 0.7751W
28-Pin SSOP-Package Example
For the 28-pin SSOP package (TJA = 1 / 0.009496 =
+105.3°C/W), the maximum allowed ambient tempera-
ture TA is given by:
TJ (max) = TA + (PD x TJA) =
+125°C = TA + (0.7751W x +105.3°C/W)
TA = +43°C
Thus, the device cannot operate safely at a maximum
package temperature of +85°C. The power dissipates
in the part need to be lowered.
I
V
R
SEG
ISET
=
×
120
450
.
RISET (k
)ISEG (mA)
25
21.6
50
10.8
100
5.4
500
1.1
>2500
LED driver disabled
Table 5. Segment-Current Selection
相关PDF资料 |
PDF描述 |
|---|---|
| PT06A-14-18P | CONN PLUG 18POS W/PINS SOLDER |
| 206613-1 | CONN RECEPT CPC 22POS STD SER 4 |
| MAX1237EUA+ | IC ADC 12-BIT 94KSPS 8-UMAX |
| MS3102E24-20P | CONN RCPT 11POS BOX MNT W/PINS |
| 206150-3 | CONN CPC PLUG 37POS W/O SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1496EPI+ | 功能描述:模数转换器 - ADC 3.5 Digit ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX14970ETP+ | 制造商:Maxim Integrated Products 功能描述:RUGGEDIZED SATA 6GBPS REDRIVER WITH HIGH ESD AND EXTENDED TE - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC REDRIVER RUGGED 6GBPS QFN 制造商:Maxim Integrated Products 功能描述:Equalizers ruggedized sata 6gbp s redriver with high |
| MAX14970ETP+T | 制造商:Maxim Integrated Products 功能描述:RUGGEDIZED SATA 6GBPS REDRIVER WITH HIGH ESD AND EXTENDED TE - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC REDRIVER SATA GEN 3 QFN 制造商:Maxim Integrated Products 功能描述:ruggedized sata 6gbp s redriver with high |
| MAX14970EVKIT# | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR MAX14970. RUGGEDIZED SATA 6GBPS REDRIVER - Boxed Product (Development Kits) 制造商:Maxim Integrated Products 功能描述:KIT EVALUATION FOR MAX14970 制造商:Maxim Integrated Products 功能描述:Equalizers MAX14970 Eval Kit |
| MAX14972CTG+ | 功能描述:USB 接口集成电路 Dual USB 3.0 Re-Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。