- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15001BEUB+ (Maxim Integrated Products)IC REG CTRLR PWM CM 10-UMAX PDF资料下载
参数资料
| 型号： | MAX15001BEUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2.5MHz |
| 占空比： | 75% |
| 电源电压： | 9.5 V ~ 24 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
Current-Mode PWM Controllers with
Programmable Switching Frequency
Current Limit
The current-sense resistor (R4 in Figure 1), connected
between the source of the MOSFET and ground, sets the
current limit. The current-limit comparator has a voltage
trip level (V CS ) of 1V. Use the following equation to cal-
culate the value of R4:
when f SW = 350kHz), C1 must store enough charge to
deliver current to the device for at least this much time.
To calculate the approximate amount of capacitance
required, use the following formula:
I g = Q gtot f SW
R 4 = CS
V
I PRI
C 1 =
(I IN + I g )(t SS )
V HYST
where I PRI is the peak current in the primary side of the
transformer which also flows through the MOSFET.
When the voltage produced by this current (through the
current-sense resistor) exceeds the current-limit com-
parator threshold, the MOSFET driver (NDRV) termi-
nates the current on-cycle within 60ns (typ). Use a
small RC network to filter out the leading-edge spikes
where I IN is the MAX15000’s internal supply current
(2mA) after startup, Q gtot is the total gate charge for
Q1, f SW is the MAX15000 ’s switching frequency
(350kHz), V HYST is the bootstrap UVLO hysteresis
(approximately 12V) and t SS is the internal soft-start
time (5.6ms).
Example: I g = (8nC) (350kHz) ? 2.8mA
on the sensed waveform when needed. Set the corner
frequency between 2MHz and 10MHz.
Applications Information
C 1 =
(2mA + 2.8mA )(5.6ms)
12 V
= 2 . 24 μ F
I C 1 = SUVR
Startup Time Considerations for Power
Supplies Using the MAX15000
The bypass capacitor at IN, C1, supplies current imme-
diately after the MAX15000 wakes up (see Figure 1).
The size of C1 and the connection configuration of the
tertiary winding determine the number of cycles avail-
Choose a 2.2μF standard value (assuming 350kHz
switching frequency).
Assuming C1 > C2, calculate the value of R1 as follows:
V C 1
( 500 ms )
able for startup. Large values of C1 increase the start-
up time but also supply gate charge for more cycles
during initial startup. If the value of C1 is too small, V IN
drops below 9.74V because NDRV does not have
R 1 ?
V IN ( MIN ) ? V SUVR
I C 1 + I START
enough time to switch and build up sufficient voltage
across the tertiary output which powers the device. The
device goes back into UVLO and does not start. Use a
low-leakage capacitor for C1 and C2.
Typically, offline power supplies keep startup times to
where V IN(MIN) is the minimum input supply voltage for
the application (36V for telecom), V SUVR is the boot-
strap UVLO wake-up level (23.6V max), I START is the IN
supply current at startup (90μA max).
For example:
less than 500ms even in low-line conditions (85VAC
input for universal offline or 36VDC for telecom applica-
tions). Size the startup resistor, R1, to supply both the
I C1 =
( 24 V )( 2 . 2 μ F )
( 500 ms )
= 0 . 105 mA
maximum startup bias of the device (90μA) and the
charging current for C1 and C2. The bypass capacitor,
C2, must charge to 9.5V and C1 to 24V, all within the
R 1 ?
( 36 V ) ? ( 12 V )
( 0 . 105 mA ) + ( 90 μ A )
= 123 . 07 k ?
desired time period of 500ms. Because of the internal
soft-start time of the MAX15000 (approximately 5.6ms
Choose a 120k ? standard value.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15002ATL+T | IC REG CTRLR BUCK PWM 40-TQFNEP |
| MAX15003ATM+T | IC REG CTRLR BUCK PWM 48TQFN-EP |
| MAX15005AAUE/V+ | IC REG CTRLR PWM CM 16-TSSOP |
| MAX15006BASA+ | IC REG LDO 5V 50MA 8-SOIC |
| MAX15008ATJ+ | IC REG LDO 5V/ADJ .3A 32TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15001BEUB+ | 功能描述:电流型 PWM 控制器 w/Programmable Switching Frequency RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX15001BEUB+T | 功能描述:电流型 PWM 控制器 w/Programmable Switching Frequency RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX15002ATL+ | 功能描述:DC/DC 开关控制器 Dual-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15002ATL+T | 功能描述:DC/DC 开关控制器 Dual-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15003ATM+ | 功能描述:DC/DC 开关控制器 Triple-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。