- 您现在的位置：买卖IC网 > PDF目录20715 > MAX15010ATJ+T (Maxim Integrated)IC REG LDO 5V/ADJ .3A 32TQFN PDF资料下载
参数资料
| 型号： | MAX15010ATJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V/ADJ .3A 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式或可调式 |
| 输出电压： | 5V，1.8 V ~ 11 V |
| 输入电压： | 5 V ~ 40 V |
| 电压 - 压降（标准）： | 0.775V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA（最小） |
| 电流 - 限制（最小）： | 330mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
Automotive 300mA LDO Voltage Regulators
with Tracker Output and Overvoltage Protector
Detailed Description
The MAX15008/MAX15010 integrate a 300mA LDO
voltage regulator, a voltage tracker, and an OVP con-
troller. These devices operate over a wide 5V to 40V
supply voltage range and are able to withstand load-
dump transients up to 45V.
The MAX15008/MAX15010 feature a 300mA LDO regu-
lator that consumes less than 70μA of current under
light-load conditions and feature a fixed 5V or an
adjustable output voltage (1.8V to 11V). Connect
FB_LDO to ground to select a fixed 5V output voltage
or select the LDO output voltage by connecting an
external resistive voltage-divider at FB_LDO. The regu-
lator sources at least 300mA of current and includes a
current limit of 330mA (min). Enable the LDO by pulling
EN_LDO high.
The tracker can be powered from the LDO input sup-
ply voltage or an independent voltage source. It is
designed to supply power to a remote sensor and is
able to handle the severe conditions in automotive
applications. Set the tracker output voltage by con-
necting a resistive voltage-divider to OUT_TRK and
connecting ADJ to the tracking source. The tracker
feedback, FB_TRK, and a separate tracker reference
voltage input, ADJ, offer the flexibility of setting the
tracker output to be lower, equal to, or higher than the
main (LDO) output. Pull EN_TRK to SGND to turn the
tracker off and keep the device in always-on, low-
quiescent-current operation.
The OVP controller (MAX15008 only) relies on an exter-
nal MOSFET with adequate voltage rating (V DSS ) to
protect downstream circuitry from overvoltage tran-
discharge. The voltage clamp also prevents the GATE-
to-SOURCE voltage from exceeding the absolute maxi-
mum rating for the V GS of the external MOSFET in case
the source terminal is accidentally shorted to 0V.
Overvoltage Monitoring (MAX15008 Only)
The OVP controller monitors the voltage at FB_PROT
and controls an external n-channel MOSFET, isolating,
or limiting the load during an overvoltage condition.
Operation in OVP switch mode or limiter mode
depends on the connection between FB_PROT and the
external MOSFET.
Overvoltage Switch Mode
When operating in OVP switch mode, the FB_PROT
divider is connected to the drain of the external
MOSFET. The feedback path consists of the voltage-
divider tapped at FB_PROT, FB_PROT ’s internal
comparator, the internal gate charge pump/gate
pulldown, and the external n-channel MOSFET (Figure
1). When the programmed overvoltage threshold is
exceeded, the internal comparator quickly pulls GATE
to ground and turns off the external MOSFET,
disconnecting the power source from the load. In this
configuration, the voltage at the source of the
MOSFET is not monitored. When the voltage at
FB_PROT decreases below the overvoltage threshold,
the MAX15008 raises the voltage at GATE, reconnecting
the load to the power source.
sients. The OVP controller drives the gate of the exter-
V IN
IN
GATE
nal n-channel MOSFET, and is configurable to operate
as an overvoltage protection switch or as a closed-loop
voltage limiter.
MAX15008
PROTECTOR
GATE Voltage (MAX15008 Only)
FB_PROT
SOURCE
OUTPUT
The MAX15008 uses a high-efficiency charge pump to
generate the GATE voltage for the external n-channel
MOSFET. Once the input voltage, V IN , exceeds the
undervoltage lockout (UVLO) threshold, the internal
charge pump fully enhances the external n-channel
MOSFET. An overvoltage condition occurs when the
voltage at FB_PROT goes above the threshold voltage,
V TH_PROT . After V TH_PROT is exceeded, GATE is quick-
ly pulled to PGND with a 63mA pulldown current. The
MAX15008 includes an internal clamp from GATE to
SOURCE that ensures that the voltage at GATE never
exceeds one diode drop below SOURCE during gate
SGND
Figure 1. Overvoltage Switch Configuration (MAX15008)
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| GBM10DCAT-S189 | CONN EDGECARD 20POS R/A .156 SLD |
| MAX8635ELA+T | IC REG LDO ADJ .3A 8UDFN |
| NCV4264ST50T3G | IC REG LDO 5V .1A SOT-223 |
| VE-J3N-CX-F4 | CONVERTER MOD DC/DC 18.5V 75W |
| ASC40DRTN-S13 | CONN EDGECARD 80POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15011ATJ+ | 功能描述:低压差稳压器 - LDO Automotive 300mA w/Switched Output RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX15011ATJ+T | 功能描述:低压差稳压器 - LDO Automotive 300mA w/Switched Output RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX15012AASA+ | 功能描述:功率驱动器IC 175V/2A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX15012AASA+T | 功能描述:功率驱动器IC 175V/2A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX15012BASA+ | 功能描述:功率驱动器IC 175V/2A High-Speed Half-B MOSFET Drvr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。