- 您现在的位置：买卖IC网 > PDF目录17278 > MAX15021EVKIT+ (Maxim Integrated Products)BOARD EVAL FOR MAX15021 PDF资料下载
参数资料
| 型号： | MAX15021EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR MAX15021 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 电流 - 输出： | 4A，2A |
| 输入电压： | 2.5 V ~ 5.5 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX15021 |
MAX15021
Dual, 4A/2A, 4MHz, Step-Down DC-DC
Regulator with Tracking/Sequencing Capability
Error Amplifier
The output of the internal voltage-mode error amplifier
(COMP_) is provided for frequency compensation (see
the Compensation-Design Guidelines section). FB_ is
the inverting input of the error amplifier. The error
amplifier has an 80dB open-loop gain and a 12MHz
CURRENT LIMIT
IN
COUNT OF 4
N CL
INITIATE HICCUP
TIMEOUT
N HT
gain bandwidth (GBW) product.
Output Short-Circuit
Protection (Hiccup Mode)
The MAX15021 features lossless, high-side peak cur-
rent limit and low-side, valley current limit. At short duty
cycles, both limits are active. At high duty cycles, only
the high-side peak current limit is active. Either limit
CLR
causes the hiccup mode count (N CL ) to increment.
IN
COUNT OF 3
R T [ k Ω ] = SW
For duty cycles less than 50%, the low-side valley cur-
rent limit is active. Once the high-side MOSFET turns off,
the voltage across the low-side MOSFET is monitored. If
this voltage does not exceed the current-limit threshold
at the end of the cycle, the high-side MOSFET turns on
normally at the start of the next cycle. If the voltage
exceeds the current-limit threshold just before the
beginning of a new PWM cycle, the controller skips that
cycle. During severe overload or short-circuit condi-
tions, the switching frequency of the device appears to
decrease because the on-time of the low-side MOSFET
extends beyond a clock cycle.
If the current-limit threshold is exceeded for more than
four cumulative clock cycles (N CL ), the device shuts
down for 8192 clock cycles (hiccup timeout) and then
restarts with a soft-start sequence. If three consecutive
cycles pass without a current-limit event, the count of
N CL is cleared (see Figure 3). Hiccup mode protects
the device against a continuous output short circuit.
The internal current limit is constant from 5.5V down to
3V and decreases linearly by 50% from 3V to 2V. See
the Electrical Characteristics table.
Thermal-Overload Protection
The MAX15021 features an integrated thermal-overload
protection with temperature hysteresis. Thermal-over-
load protection limits the total power dissipation in the
device and protects it in the event of an extended ther-
mal fault condition. When the die temperature exceeds
+160°C, an internal thermal sensor shuts down the
device, turning off the internal power MOSFETs and
allowing the die to cool. After the die temperature falls
by +15°C, the part restarts with a soft-start sequence.
12
N CLR
CLR
Figure 3. Hiccup-Mode Block Diagram
Startup into a Prebiased Output
(Sequencing Mode)
In sequencing mode, the regulators start into a prebi-
ased output and soft-stop is disabled. During soft-start,
the complementary switching sequence is inhibited until
the PWM comparator commands its first PWM pulse.
Until then, the converters do not sink current from the
outputs. The first PWM pulse occurs when the ramping
reference voltage increases above the FB_ voltage.
PWM Controllers
Design Procedure
Setting the Switching Frequency
Connect a 4.2k Ω to 33k Ω resistor from RT to SGND to
program the switching frequency from 500kHz to
4MHz. Calculate the resistor connected to RT using the
following equation:
f [kHz] × 1.067[V]
32 [ μ A ] × 4[MHz]
Higher frequencies allow designs with lower inductor
values and less output capacitance. At higher switch-
ing frequencies core losses, gate-charge currents, and
switching losses increase. When operating from V AVIN
≤ 3V, the switching frequency (f SW ) should be derated
to 3MHz (maximum).
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| 050R24-102B | CABLE FLAT FLEX 24POS 0.5MM 4" |
| GCC17DCMD | CONN EDGECARD 34POS .100" WW |
| AIRD-06-222K | INDUCTOR 2200UH 0.8A 10% |
| ECC08DRYI | CONN EDGECARD 16POS DIP .100 SLD |
| 591D157X0010C2T20H | CAP TANT 150UF 10V 20% 2812 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15021EVKIT+ | 功能描述:电源管理IC开发工具 MAX15021 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15022ATI+ | 功能描述:直流/直流开关调节器 Dual 4A/2A 4MHz w/Dual LDO Ctlr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15022ATI+T | 功能描述:直流/直流开关调节器 Dual 4A/2A 4MHz w/Dual LDO Ctlr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15022EVKIT+ | 功能描述:电源管理IC开发工具 MAX15022 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15023ETG/V+ | 功能描述:DC/DC 开关控制器 4.5-28V Input Dual Out Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。