- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15023ETG+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM 24TQFNEP PDF资料下载
参数资料
| 型号： | MAX15023ETG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 24TQFNEP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 1MHz |
| 占空比： | 87.5% |
| 电源电压： | 4.5 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MAX15023
Wide 4.5V to 28V Input, Dual-Output
Synchronous Buck Controller
Setting the Cycle-by-Cycle, Low-Side,
Source Peak Current Limit
The minimum current-limit threshold must be high
enough to support the maximum expected load current
with the worst-case low-side MOSFET on-resistance
value since the low-side MOSFET’s on-resistance is
used as the current-sense element. The inductor ’s
cycle-by-cycle, low-side, source peak current occurs at
I LOAD(MAX) minus half the ripple current. The ripple cur-
rent is maximum when the inductor value is at the lower
limit of its specified tolerance. The minimum value of
the current-limit threshold voltage (V ITH ) should be
greater than the voltage on the low-side MOSFET dur-
ing the ripple-current valley:
I RMS has a maximum value when the input voltage
equals twice the output voltage (V IN = 2V OUT ), so
I RMS(MAX) = I LOAD(MAX) /2.
Choose an input capacitor that exhibits less than +10°C
temperature rise at the RMS input current for optimal
long-term reliability.
The input voltage ripple is composed of ? V Q (caused
by the capacitor discharge) and ? V ESR (caused by the
ESR of the capacitor). Use low-ESR ceramic capacitors
with high ripple current capability at the input. Assume
the contribution from the ESR and capacitor discharge
are equal to 50%. Calculate the input capacitance and
ESR required for a specified input voltage ripple using
the following equations:
V ITH > R DS ( ON , MAX ) × I LOAD ( MAX ) × ? 1 ?
?
I OUT +
? LIR ?
? 2 ?
where R DS(ON) is the on-resistance of the low-side
MOSFET in ohms. Use the maximum value for R DS(ON)
where:
ESR IN =
? V ESR
? I L
2
from the low-side MOSFET’s data sheet.
To adjust the current-limit threshold, connect a resistor
(R LIM_ ) from LIM_ to SGND. The relationship between
the current-limit threshold (V ITH_ ) and R LIM_ is:
and:
? I L =
(V IN ? V OUT ) × V OUT
V IN × f SW × L
C IN = OUT
R LIM _ =
10 × V ITH _
50 μ A
I × D(1 ? D)
? V Q × f SW
D = OUT
where R LIM_ is in k ? and V ITH_ is in mV.
An R LIM_ resistance range of 6k ? to 60k ? corresponds
to a current-limit threshold of 30mV to 300mV. When
adjusting the current limit, use 1% tolerance resistors to
minimize errors in the current-limit threshold setting.
Input Capacitor
The input filter capacitor reduces peak currents drawn
from the power source and reduces noise and voltage
ripple on the input caused by the circuit’s switching.
The two converters of the MAX15023 run 180° out-of-
phase, thereby, effectively doubling the switching fre-
quency at the input and lowering the input RMS current.
The input ripple waveform would be unsymmetrical due
to the difference in load current and duty cycle between
converter 1 and converter 2. In fact, the worst-case input
RMS current occurs when only one controller is operat-
ing. The converter delivering the highest output power
(V OUT x I OUT ) must be used in the formulas below:
The input capacitor RMS current requirement (I RMS ) is
defined by the following equation:
where:
V
V IN
All equations listed above are valid under the assump-
tion that the input ports of both converters can be
merged in the physical layout, so that only one input
capacitor truly serves both converters. If this is not the
case, additional low-ESR, low-ESL ceramic capacitors
should be locally placed on each converter’s input port,
connected between the drain of the high-side MOSFET
and the source of the low-side MOSFET.
Output Capacitor
The key selection parameters for the output capacitor
are capacitance value, ESR, and voltage rating. These
parameters affect the overall stability, output ripple volt-
age, and transient response. The output ripple has two
components: variations in the charge stored in the out-
put capacitor, and the voltage drop across the capaci-
tor’s ESR caused by the current flowing into and out of
the capacitor:
18
I RMS = I LOAD ( MAX )
V OUT ( V IN ? V OUT )
V IN
? V RIPPLE ? ? V ESR + ? V Q
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15026CATD+T | IC REG CTRLR BUCK PWM VM 14TDFN |
| MAX15027ATB+T | IC REG LDO ADJ 1A 10-TDFN |
| MAX15030ATB+T | IC REG LDO ADJ .5A 10-TDFN |
| MAX15031ATE+ | IC BOOST CONV/CURRENT MON 16TQFN |
| MAX15032ATA+T | IC REG BOOST ADJ 1A 8TDFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15023ETG/V+ | 功能描述:DC/DC 开关控制器 4.5-28V Input Dual Out Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15023ETG/V+T | 功能描述:DC/DC 开关控制器 4.5-28V Input Dual Out Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15023ETG+ | 功能描述:DC/DC 开关控制器 4.5-28V Input Dual Out Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15023ETG+ | 制造商:Maxim Integrated Products 功能描述:BUCK CONTROLL SYNC 4.5~28V 24QFN 制造商:Maxim Integrated Products 功能描述:BUCK CONTROLL, SYNC, 4.5~28V, 24QFN |
| MAX15023ETG+T | 功能描述:DC/DC 开关控制器 4.5-28V Input Dual Out Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。